Abstract:Flow fields near the turbine vane endwall region are very complicated due to the presence of high three-dimensional passage vortices and endwall secondary flows. This makes it challenging for the endwall to be effectively cooled by using traditional endwall cooling methods, such as impingement cooling combined with local film cooling inside the vane passage. One effective endwall cooling scheme: coolant injection flow through discrete holes upstream of the vane leading edge on the endwall, has been considered by many gas turbine companies. The present paper focuses on endwall film cooling effectiveness evaluation with upstream coolant injection through discrete holes. Detailed experimental and numerical studies on endwall heat transfer and cooling performance with coolant injection flow through upstream discrete holes are presented in this paper. High-resolution heat transfer coefficient (HTC) and adiabatic film cooling effectiveness values were measured using a transient infrared thermography technique on an axisymmetric contoured endwall. The endwall tested was a scaled up inner endwall of an industrial transonic turbine vane with double-row discrete cylindrical film cooling holes located 0.39Cx upstream of the vane leading edge. The tests were performed in a transonic linear cascade blowdown wind tunnel facility. Conditions were representative of a land-based power generation turbine with exit Mach number of 0.85 corresponding to exit Reynolds number of 1.5 x 10(6), based on exit condition and axial chord length. A high turbulence level of 16% with an integral length scale of 3.6%P was generated using inlet turbulence grid to reproduce the typical turbulence conditions in real turbine. Low temperature air was used to simulate the typical coolant-to-mainstream condition by controlling two parameters of the upstream coolant injection flow: mass flowrate to determine the coolant-to-mainstream blowing ratio (BR = 2.5, 3.5), and gas temperature to determine the density ratio (DR = 1.2). To highlight the interactions between the upstream coolant flow and the passage secondary flow combined with the influence on the endwall heat transfer and cooling performance, a comparison of CFD predictions with experimental results was performed by solving steady-state Reynolds-averaged Navier-Stokes (RANS) using the commercial CFD solver ansys fluent V.15. A detailed numerical method validation was performed for four different Reynolds-averaged turbulence models. The realizable kappa-epsilon model was validated to be suitable to obtain reliable numerical solution. The influences of a wide range of coolant-to-mainstream blowing ratios (BR = 1.0, 1.5, 1.9, 2.5, 3.0, 3.5) were numerically studied. Complex interactions between coolant injections and secondary flows in vane passage were presented and discussed. An optimal value of the blowing ratio for the present upstream discrete film hole is also suggested based on the current study. Results indicate that for lower values of BR, the endwall coolant coverage from the upstream double-row discrete holes is strongly controlled by the passage secondary flow, thus the cooling effectiveness is very poor. As the BR increases, the strong secondary flow in vane passage can be suppressed by the coolant injections and begin to be almost eliminated when BR increases to a critical value (BR = 2.5-3.0). Beyond the critical BR, most of the injected coolant begins to lift off from the endwall and penetrate significantly into the mainstream flow, yielding inefficient endwall cooling performance.

Influence of the Upstream Slot Geometry on the Endwall Cooling and Phantom Cooling of Vane Suction Side Surface

Effects of the Mainstream Turbulence Intensity and Slot Injection Angle on the Endwall Cooling and Phantom Cooling of the Vane Suction Side Surface

Effects of the Swirling Coolant Jet from the Upstream Slot on the Vane Endwall Cooling and the Vane Suction Side Phantom Cooling

Effects of the Cooling Configurations Layout Near the First-Stage Vane Leading Edge on the Endwall Cooling and Phantom Cooling of the Vane Suction Side Surface

Numerical Study on the Effects of Slot Injection Configuration and Endwall Alignment Mode on the Film Cooling Performance of Vane Endwall

Effects of the Leading Edge Injection Slot on the Film Cooling and Heat Transfer Performance of the Vane Endwall

Influence of the Pressure Side Injection Slot on the Cooling Performance of Endwall Surface

Effects of Upstream Slot Geometry on the Endwall Aerothermal Performance of a Gas Turbine Blade under Different Ejection Angle Conditions

Numerical investigation on film cooling and aerodynamic performance for gas turbine endwalls with upstream vane-type and cascade-type slots

Effect of the Slot Jet Impingement on the Cooling Performance of the Vane Endwall

Turbine Vane Endwall Film Cooling and Pressure Side Phantom Cooling Performances with Upstream Coolant Flow at Various Injection Angles

Effects of Location and Profile of Upstream Slot on the Endwall Aerothermal Performance of a Gas Turbine Blade

Experimental and numerical study on film cooling effectiveness of an annular cascade endwall with different slot configuration

Effects of Upstream Step Geometries on Endwall Film Cooling and Phantom Cooling Performances of a Transonic Turbine Vane

Effects of location and geometry of slot on film cooling performance of end-wall

Numerical Study on the Influence of Purge Slot Shapes on the Film Cooling Performance of Endwall with the Mainstream Swirl

Effects of Trenched Film Hole Configurations on the Endwall Film Cooling and Suction Side Phantom Cooling

Numerical Investigation of the Cooling Flow Downstream of a Turbine Guide Vane Trailing Edge Slot

Influence of Endwall 2D Contouring on Endwall Adiabatic Cooling Effectiveness and Aerodynamic Performance

The Effects of Axisymmetric Convergent Contouring and Blowing Ratio on Endwall Film Cooling and Vane Pressure Side Surface Phantom Cooling Performance

Endwall Heat Transfer and Cooling Performance of a Transonic Turbine Vane with Upstream Injection Flow