Abstract:This study investigates the correspondence between film cooling flow and convective heat transfer augmentation on the trailing edge cutback surface of a turbine blade, proposing a novel approach with oblong dimples in V-pattern pairs to enhance the cooling performance. Using transient infrared thermography coupled with the Impulse Response Method, detailed measurements of adiabatic film cooling effectiveness and heat transfer coefficients were obtained. Scale-Adaptive-Simulations (SAS) were also utilized to delve into the turbulent flow dynamics and elucidate the mechanisms behind the enhanced cooling performance. The experiments and simulations were conducted for a trailing edge model equipped with pin fin arrays inside the coolant channel and a land feature on the cutback surface. Overall, three different cutback surfaces were investigated: a smooth baseline geometry and two dimpled surfaces with different geometrical orientation. The cooling performance was evaluated over a range of blowing ratios spanning between 0.5 and 2. The results indicate that as the blowing ratio increases, there is a corresponding enhancement in both the adiabatic film cooling effectiveness and the heat transfer coefficients across all three cutback surface configurations. However, the dimpled patterns, when compared to the smooth one, showed a broader coolant film distribution and facilitated the formation of small-scale vortices, which in turn improved the heat transfer efficiency. Specifically, surfaces with a tighter arrangement of dimples exhibited superior cooling effects, achieving approximately 5.0 % increase in the film cooling effectiveness and an 8.9 % boost in the convective heat transfer coefficients. Moreover, the strategic placement of V-pattern dimples effectively steers the coolant flow close to the wall towards the land, significantly enhancing coolant spread and thus offering improved thermal protection for the land area. These findings hold the potential to significantly improve the performance of aero-engines by optimizing the trade-off between thermal management and aerodynamic efficiency of turbine blades.

Predictions of Enhanced Heat Transfer of an Internal Blade Tip-Wall with Hemispherical Dimples or Protrusions

Numerical Prediction on Turbine Blade Internal Tip Cooling with Pin-Fin and Dimple/protrusion Structures

Experimental and Numerical Investigation of Heat Transfer and Friction Performance for Turbine Blade Tip Cap with Combined Pin-Fin-dimple/protrusion Structure

Transpiration Cooling of High Pressure Turbine Vane with Optimized Porosity Distribution

Surface temperature reduction by using dimples/protrusions in a realistic turbine blade trailing edge

Numerical Predictions on Fluid Flow and Heat Transfer in U-Shaped Channel with the Combination of Ribs, Dimples and Protrusions under Rotational Effects

Influence of Dimple Diameter and Depth on Heat Transfer of Impingement-Cooled Turbine Leading Edge with Cross-Flow and Dimple

Vortical Structures and Heat Transfer Augmentation of a Cooling Channel in a Gas Turbine Blade with Various Arrangements of Tip Bleed Holes

Film cooling enhancement over oblong-dimpled cutback surfaces for the trailing edge of turbine blades

On the Heat Transfer and Flow Structures’ Characteristics of the Turbine Blade Tip Underside With Dirt Purge Holes at Different Locations by Using Topological Analysis

Effects of Channel Outlet Configuration and Dimple/Protrusion Arrangement on the Blade Trailing Edge Cooling Performance

HEAT TRANSFER ENHANCEMENT FOR GAS TURBINE BLADE LEADING EDGE COOLING USING CURVED DOUBLE-WALL/VORTEX COOLING WITH VARIOUS DISTURBING OBJECTS

Numerical Study on Flow and Heat Transfer Performance of Rectangular Heat Sink with Compound Heat Transfer Enhancement Structures

Thermo-hydraulic performance inside convergent rectangle channel with large-deformed dimples

Heat Transfer Enhancement In A Rectangular Channel With The Combination Of Ribs, Dimples And Protrusions

Heat transfer enhancement by inserting a radiation enhancement plate in turbine blade internal cooling channel

Experimental Study on Flow Behavior and Heat Transfer Enhancement With Distinct Dimpled Gas Turbine Blade Internal Cooling Channel

Experimental and Computational Assessment into the Heat Transfer for the Blade Multicavity Tips

CONJUGATE HEAT TRANSFER CHARACTERISTICS IN A VANE BLADE WITH DIFFERENT DIMPLE/PROTRUSION/PIN FIN CONFIGURATION FOR TRAILING REGION

Experimental Study on the Conjugate Heat Transfer of Double-Wall Turbine Blade Components With/without Pins

Heat Transfer Characteristics of a Dimpled/protrusioned Pin Fin Wedge Duct with Different Converging Angles for Turbine Blades