Abstract:Low cycle fatigue cropping technology is a new type of cropping technology with advantages such as no chip waste and low load need. Numerous studies have shown that increasing the fatigue frequency or increasing the displacement load can improve the cropping efficiency, but at the same time, it will reduce the quality of the cross-section and cannot achieve a balance between high efficiency and high quality of cross-section. In response to this issue, this paper found the phenomenon of transition of fracture modes (from fatigue mode to tensile fracture mode) of 6061Al material in LCFC process, and proposed the Active Load Reducing Optimization Strategy for 6061Al in LCFC, which achieves a significant improvement in quality of cross-section with a slight loss of cropping efficiency. Firstly, this paper studied the crack fracture mechanism of 6061Al bar under different displacement loads in the LCFC process. It was found that the transition of crack propagation mode in 6061Al- LCFC process was the main reason for the increase in cross-section roughness. The crack propagation mode changed from fatigue propagation to tensile fracture propagation during the LCFC process, and the roughness of the area significantly increased under the tensile fracture propagation mode. Further research has found that the fundamental reason for the contradiction between the cropping efficiency and section quality of 6061Al is the change in time of crack propagation mode transition and tensile fracture zone area under different displacement loads. Finally, the LCFC process was modeled in a time dimension using acoustic emission(AE) technology, and it was divided into three stages according to the AE signals and the fracture mechanism. As a result, an active load reducing optimization strategy for LCFC process was developed to delay the occurrence of tensile fracture propagation modes. Experiments have shown that compared to the traditional LCFC cropping strategy using constant displacement loads, the active load reducing strategy proposed in this paper can reduce the proportion of tensile fracture area, achieve a significant improvement in quality of cross-section with a slight loss of cropping efficiency, thus achieving a balance between efficiency and section quality to some extent. At the same time, an LCFC process section quality efficiency evaluation index with dual weights of efficiency and section quality has been proposed, which can assist in selecting LCFC active load reducing strategy parameters with consideration of efficiency and section quality weights.

The Investigation of the Optimization Scheme of the Low-Cycle Fatigue Cropping Based on the Acoustic Emission Technique

The Investigation of Fracture Characteristics and Process Optimization of Low-Cycle Fatigue Cropping by Using an AET-based Multi-Sensor System

The Investigation of Low-Cycle Fatigue Crack Propagation of 16 Mn Eccentric Bar Based on the Acoustic Emission Technique

Research on Active Load Reducing Optimization Strategy for 6061al Low Cycle Fatigue Cropping Process Based on Crack Propagation Mode Transformation

Improvement Of Cyclic Void Growth Model For Ultra-Low Cycle Fatigue Prediction Of Steel Bridge Piers

Study on the Prediction Method of the Ultra-Low-Cycle Fatigue Damage of Steel

Optimization Scheme of the Precision Separation Process of the Notched Bar Based on the Acoustic Emission Hit Energy Angle

Experimental investigation on new low cycle fatigue precision cropping process

The Investigation of Reasonable Range of Initial Load of Low-Cycle Fatigue Cropping for Notched Bars

Experimental Study on New Low Cycle Fatigue Precision Cropping Process

A Proposal on Ultra-Low Cycle Fatigue Damage Evaluation of Structural Steels

Theoretical and Experimental Investigation on Influence of Load Control Strategy of LY12 Duralumin Alloy Bar Fine Cropping Process

Acoustic emission characteristics in eccentric rotary cropping process of stainless steel tube

Experimental investigation of the effect of the circumferential loading of a rotary striking action cropping system

Study on the Cracking Time in Low-stress Precision Cropping Based on Acoustic Emission Technology

The Ideal Control Curves of Low Stress Precision Cropping Experimental Study on Metal Bar

Research on Hydraulic Compensation and Variable Loading Arm for a New-Type Low-Stress Cropping System

An Approach to Estimate the Low Cycle Fatigue Probabilistic Curves of PBF-LB/M 316L Steel from Small Size Datasets Using the Remora Optimization Algorithm

Low Cycle Fatigue Property and Fracture Behavior of Low Yield Point Steels

Research on the deflection of metal bar with V-shaped notch in low-stress cropping process

Research on bar deflection of low-stress cropping process under bending-shear coupling effect