Abstract:Low cycle fatigue cropping technology is a new type of cropping technology with advantages such as no chip waste and low load need. Numerous studies have shown that increasing the fatigue frequency or increasing the displacement load can improve the cropping efficiency, but at the same time, it will reduce the quality of the cross-section and cannot achieve a balance between high efficiency and high quality of cross-section. In response to this issue, this paper found the phenomenon of transition of fracture modes (from fatigue mode to tensile fracture mode) of 6061Al material in LCFC process, and proposed the Active Load Reducing Optimization Strategy for 6061Al in LCFC, which achieves a significant improvement in quality of cross-section with a slight loss of cropping efficiency. Firstly, this paper studied the crack fracture mechanism of 6061Al bar under different displacement loads in the LCFC process. It was found that the transition of crack propagation mode in 6061Al- LCFC process was the main reason for the increase in cross-section roughness. The crack propagation mode changed from fatigue propagation to tensile fracture propagation during the LCFC process, and the roughness of the area significantly increased under the tensile fracture propagation mode. Further research has found that the fundamental reason for the contradiction between the cropping efficiency and section quality of 6061Al is the change in time of crack propagation mode transition and tensile fracture zone area under different displacement loads. Finally, the LCFC process was modeled in a time dimension using acoustic emission(AE) technology, and it was divided into three stages according to the AE signals and the fracture mechanism. As a result, an active load reducing optimization strategy for LCFC process was developed to delay the occurrence of tensile fracture propagation modes. Experiments have shown that compared to the traditional LCFC cropping strategy using constant displacement loads, the active load reducing strategy proposed in this paper can reduce the proportion of tensile fracture area, achieve a significant improvement in quality of cross-section with a slight loss of cropping efficiency, thus achieving a balance between efficiency and section quality to some extent. At the same time, an LCFC process section quality efficiency evaluation index with dual weights of efficiency and section quality has been proposed, which can assist in selecting LCFC active load reducing strategy parameters with consideration of efficiency and section quality weights.

Experimental investigation on new low cycle fatigue precision cropping process

Experimental Study on New Low Cycle Fatigue Precision Cropping Process

Improvement Of Cyclic Void Growth Model For Ultra-Low Cycle Fatigue Prediction Of Steel Bridge Piers

Investigation on the Crack Initiation of V-Shaped Notch Tip in Precision Cropping

The Investigation of Low-Cycle Fatigue Crack Propagation of 16 Mn Eccentric Bar Based on the Acoustic Emission Technique

The Investigation of Fracture Characteristics and Process Optimization of Low-Cycle Fatigue Cropping by Using an AET-based Multi-Sensor System

Research on Active Load Reducing Optimization Strategy for 6061al Low Cycle Fatigue Cropping Process Based on Crack Propagation Mode Transformation

Experimental investigation of the effect of the circumferential loading of a rotary striking action cropping system

The Investigation of the Optimization Scheme of the Low-Cycle Fatigue Cropping Based on the Acoustic Emission Technique

Research on Variable Frequency-Loading Curve in Precision Cropping System with High-Speed and Centrifugal Action

Research on the deflection of metal bar with V-shaped notch in low-stress cropping process

Investigation on Fatigue Strength and Notch Effect of 17-4PH Blade Root

The Investigation of Reasonable Range of Initial Load of Low-Cycle Fatigue Cropping for Notched Bars

Research on Critical Loading Force in Precision Cropping System Based on Hydraulic Compensation

The Ideal Control Curves of Low Stress Precision Cropping Experimental Study on Metal Bar

Research on Hydraulic Compensation and Variable Loading Arm for a New-Type Low-Stress Cropping System

A New Approach to Precision Cropping with Radial Forging

Experimental Study on New Precision Cropping Process for Metal Bars

Research on a new type of precision cropping method with variable frequency vibration

Investigation on new type of precision cropping with variant frequency vibration method

Investigation on the influences of clearance and notch-sensitivity on a new type of metal-bar non-chip fine-cropping system