Abstract:Development of a cabbage harvester is an efficient approach to change the traditional way of harvesting cabbage in China. Since cutting is the crucial process, the cutter design is one of the key techniques for the development of cabbage harvester. In order to obtain the best cutting position and cutting combination, taking the cabbage roots as the experimental materials, cutting property tests and chemical composition detection were carried out respectively. The maximum cutting force and average cutting force were taken into consideration as cutting properties. Load-displacement curves on different diameters were sampled depending on the designed test apparatus when the cutting combination was set constantly as two-point support, vertical cutting and the cutting speed of 100 mm/min. The moisture content and crude fiber content, which are the main chemical composition of cabbage root, were measured on the same diameters according to standard process. The relationships between cutting forces and chemical composition were analyzed. The results demonstrated that the maximum cutting force and average cutting force can be fit with the quadratic polynomial of diameters, and F values of the two equations reached to 251.67 and 360.62 respectively and coefficients of determination (R2) were 0.9636 and 0.9743 respectively. Both the curves declined as the cutting diameters increased and got the lowest when the diameters ranged from 30-35 mm which would be the best cutting position. From the space structure of cabbage root, it’s also the most suitable cutting position that is 10-15 mm above the bottom leaves. Multiple linear regression (MLR) was applied to establish the relationships of maximum force, average force with crude fiber content. The results proved that the main factor affecting cutting properties is crude fiber content. Mixed levels orthogonal table (22×32) was utilized to conduct the orthogonal test to obtain the best cutting position considering the factors of support mode, cutting mode, inclining mode and cutting speed which should be determined on the basis of the cabbage harvester designed previously. In the orthogonal test, there were 9 tests and 5 repetitions were conducted for each test. The maximum force and average force were obtained from the load-displacement curves. The orthogonal test results showed that:1) Support mode and cutting speed had significant influences on maximum cutting force and average cutting force, cutting mode had significant influence on maximum cutting force but had no influence on average cutting force, and inclining mode had no influence on maximum cutting force or average cutting force. 2) Based on index minimality of maximum force and average force, the best cutting combination was under the conditions of single point support mode, sliding cutting mode, downward inclining mode and the low cutting speed (50 mm/min). This research can provide a reference for design of the cabbage harvester cutter and optimization of cutting combination.

Research on Hydraulic Compensation and Variable Loading Arm for a New-Type Low-Stress Cropping System

Research on the deflection of metal bar with V-shaped notch in low-stress cropping process

Research on bar deflection of low-stress cropping process under bending-shear coupling effect

A multiple rolling-point loading method for low-stress equal-radial-depth cropping

Design and Control of Multilevel Loadings Hydraulic System of Direct Shear Apparatus

Analysis and Test of Splitting Failure in the Cutting Process of Cabbage Root

Optimization of a Whole-Stalk Operating System after Sugarcane Base Cutting

Effect of symmetrical position notching on cracking and cross-section quality of thick-walled metal tube under low-stress cropping

Influence of contact parameters on the wear characteristics of fixture-bar friction pair in low-stress cropping

Optimization of cutting position and mode for cabbage harvesting

Optimisation and dynamic simulation of a conveying and top breaking system for whole-stalk sugarcane harvesters

Simulation Optimization and Experimental Validation of Hydraulic Impact in Pruning Machines

Optimisation and Finite Element Simulation of the Chopping Process for Chopper Sugarcane Harvesting

DESIGN AND EXPERIMENT OF TRANSVERSE AXIAL FLOW CORN FLEXIBLE THRESHING DEVICE

Design and Experiment on Gripping Delivery Mechanism for Vertical-rollers Type of Corn Harvester

Research On Mechanics Properties Of Crop Stalks: A Review

Revised Design and Experiment on Small-Sized Whole-Stalk Sugarcane Harvester.

DESIGN AND EXPERIMENTAL STUDY OF FLEXIBLE THRESHING DEVICE FOR LONGITUDINAL AXIAL FLOW CORN

DEVELOPMENT AND TEST OF CORN STRAW KNEADING AND CONVEYING DEVICE

Design and Experiment on the Control System of Electro-hydraulic Plow Depth of Tractor Hydraulic Hitch Mechanism

Optimization Design and Experiment of Ear-Picking and Threshing Devices of Corn Plot Kernel Harvester