Abstract:<p>Fly ash (FA) is a common industrial by-product, which is usually used as raw materials of alkali-activated geopolymer or cement additive. However, there are few studies on phosphoric acid-based geopolymer cement synthesized with FA. In this study, FA phosphoric acid-based geopolymer (FAPG) was prepared by using low-calcium FA as raw material and phosphoric acid (PA) as reactant at room temperature. Microscopic properties and geopolymerization mechanism were studied by X-ray diffraction, scanning electron microscopy, mercury intrusion porosimetry, nuclear magnetic resonance instrument and Fourier transform infrared spectroscopy. The hydration characteristics were studied by isothermal calorimetry, and the thermal properties were explored by thermogravimetric analysis. Additionally, the setting time, compressive strength, pH and electrical conductivity of FAPG were measured. The results indicated that room-temperature cured FAPG paste activated with 50% PA and 0.3 liquid–solid mass ratio (L/S) yielded a maximum compressive strength during 0–90 days of curing. As curing time increased, the strength increased for FAPG with 50% PA, but increased at first and then scarcely increased for other FAPG pastes. The compressive strength decreased with L/S increasing. As curing time increased, the pH increased and electrical conductivity decreased. The initial and final setting time, and fluidity decreased with increasing PA concentration but increased with L/S increasing. The FAPG paste was a composite structure composed of crystalline and amorphous phase. The crystalline phase was composed of Brushite, Monetite and Berlinite, and the amorphous phase was composed of -Al-O-P-, -Si-O-P- and Si-O-Al-O-P- units. The average pore diameter of FAPG ranged from 37.38 to 64.44 nm. Heating to 1200 °C, FAPG paste presented four stages of mass loss. The total hydration heat increased with PA concentration increasing.</p>

The effect of different types of class F fly ashes on the mechanical properties of geopolymers cured at ambient environment

An efficient approach for sustainable fly ash geopolymer by coupled activation of wet-milling mechanical force and calcium hydroxide

Synthesis Factors Affecting Mechanical Properties, Microstructure, and Chemical Composition of Red Mud–fly Ash Based Geopolymers

Effect of Fine Aggregate Particle Characteristics on Mechanical Properties of Fly Ash-Based Geopolymer Mortar

Impacts of Alkaline Washing Pretreatment on Municipal Solid Waste Incineration Fly Ash (MSWI FA) and Resulting Geopolymers

Experimental study on full-volume fly ash geopolymer mortars: Sintered fly ash versus sand as fine aggregates

Study of Manufacture Process and Properties of Fly Ash-Based Geopolymers

Properties of geopolymer based on fly ash

Effect of Waste Glass Powder and Bamboo Fiber on the Physico-Mechanical Properties and High-Temperature Behavior of a Fly Ash-Based Geopolymer

A high-strength red mud–fly ash geopolymer and the implications of curing temperature

Physico-chemical properties and durability of a fly-ash-based geopolymer

Residual water and interfacial bonding effects on the mechanical performance of CNT/fly ash geopolymer binder

Feasibility analysis of the preparation of geopolymers from different types of coal based ash: Reaction, synthesis, and properties

Low-carbon enhancement of fly ash geopolymer concrete: Lateral deformation, microstructure evolution and environmental impact

Utilization of Calcium Carbide Residue as Solid Alkali for Preparing Fly Ash-Based Geopolymers: Dependence of Compressive Strength and Microstructure on Calcium Carbide Residue, Water Content and Curing Temperature

Efflorescence of fly ash-based geopolymer mortars under quasinatural conditions: The relationship between curing temperature, ion transport, and compressive strength

Solidification of (Pb–Zn) mine tailings by fly ash-based geopolymer I: influence of alkali reagents ratio and curing condition on compressive strength

Reaction Kinetics of Red Mud-Fly Ash Based Geopolymers: Effects of Curing Temperature on Chemical Bonding, Porosity, and Mechanical Strength

Low-carbon wet-ground fly ash geopolymer activated by single calcium carbide slag

Chloride resistance of class C/class F fly ash-based geopolymer mortars with different strength grades

Mechanical and microscopic properties of fly ash phosphoric acid-based geopolymer paste: A comprehensive study