Abstract:<p>Fly ash (FA) is a common industrial by-product, which is usually used as raw materials of alkali-activated geopolymer or cement additive. However, there are few studies on phosphoric acid-based geopolymer cement synthesized with FA. In this study, FA phosphoric acid-based geopolymer (FAPG) was prepared by using low-calcium FA as raw material and phosphoric acid (PA) as reactant at room temperature. Microscopic properties and geopolymerization mechanism were studied by X-ray diffraction, scanning electron microscopy, mercury intrusion porosimetry, nuclear magnetic resonance instrument and Fourier transform infrared spectroscopy. The hydration characteristics were studied by isothermal calorimetry, and the thermal properties were explored by thermogravimetric analysis. Additionally, the setting time, compressive strength, pH and electrical conductivity of FAPG were measured. The results indicated that room-temperature cured FAPG paste activated with 50% PA and 0.3 liquid–solid mass ratio (L/S) yielded a maximum compressive strength during 0–90 days of curing. As curing time increased, the strength increased for FAPG with 50% PA, but increased at first and then scarcely increased for other FAPG pastes. The compressive strength decreased with L/S increasing. As curing time increased, the pH increased and electrical conductivity decreased. The initial and final setting time, and fluidity decreased with increasing PA concentration but increased with L/S increasing. The FAPG paste was a composite structure composed of crystalline and amorphous phase. The crystalline phase was composed of Brushite, Monetite and Berlinite, and the amorphous phase was composed of -Al-O-P-, -Si-O-P- and Si-O-Al-O-P- units. The average pore diameter of FAPG ranged from 37.38 to 64.44 nm. Heating to 1200 °C, FAPG paste presented four stages of mass loss. The total hydration heat increased with PA concentration increasing.</p>

Experimental study on full-volume fly ash geopolymer mortars: Sintered fly ash versus sand as fine aggregates

Effect of Fine Aggregate Particle Characteristics on Mechanical Properties of Fly Ash-Based Geopolymer Mortar

Study on the Effect of Recycled Fine Aggregate Qualities on Fly Ash/GGBS-Based Geopolymer Mortar

Experimental Study on Fabrication of Environment-Friendly Concrete by Solidifying Aeolian Sand and Natural Gravel with Fly Ash-Based Geopolymer

Effect of Fly Ash Content on Rheological Properties of Self-compacting Geopolymer Mortar

Physico-chemical properties and durability of a fly-ash-based geopolymer

Replacement of Natural Sand with Expanded Vermiculite in Fly Ash-Based Geopolymer Mortars

Mechanical behavior and microstructure evolution of slag-fly ash based geopolymer stabilized sand

Mechanical and microscopic properties of fly ash phosphoric acid-based geopolymer paste: A comprehensive study

Characterization of Geopolymer Masonry Mortars Incorporating Recycled Fine Aggregates

Mechanical Properties, Permeability and Microstructure of Steam-Cured Fly Ash Mortar Mixed with Phosphogypsum

An efficient approach for sustainable fly ash geopolymer by coupled activation of wet-milling mechanical force and calcium hydroxide

Factors affecting the property of open-cell fly ash-based porous geopolymer via replica method

Interfacial Behavior of Slag, Fly Ash, and Red Mud-Based Geopolymer Mortar with Concrete Substrate: Mechanical Properties and Microstructure

Influence of Activators on Mechanical Properties of Modified Fly Ash Based Geopolymer Mortars

Efflorescence of fly ash-based geopolymer mortars under quasinatural conditions: The relationship between curing temperature, ion transport, and compressive strength

The Effect of Different Curing Temperatures on the Properties of Geopolymer Reinforced with Micro Steel Fibers

Effect of Replacing Fine Aggregate with Fly Ash on the Performance of Mortar

Study on the Reinforced Properties of Geopolymer Fibers with a Sustainable Development Role

Expansion in low calcium fly ash-based geopolymer concrete: chemical factors influenced by silica fume and NaOH concentration

Utilization of Calcium Carbide Residue as Solid Alkali for Preparing Fly Ash-Based Geopolymers: Dependence of Compressive Strength and Microstructure on Calcium Carbide Residue, Water Content and Curing Temperature