Abstract:This article focuses on study of the microstructural and textural evolution, as well as the recrystallization kinetics under different cold‐rolling methods and their influencing mechanism on the properties of the thin‐gauge 3.5%Si nonoriented silicon steel, so as to obtain the best production process, that is, secondary cold rolling with an intermediate annealing temperature of 900 °C. The microstructural and textural evolution, as well as the recrystallization kinetics under different cold‐rolling methods and their influencing mechanism on the properties of the thin‐gauge 3.5%Si nonoriented silicon steel, are investigated by electron backscattering diffraction, X‐ray diffractometer, tensile, and magnetic properties test. The results indicate that compared with the primary cold‐rolling process, the reduction rate of secondary cold‐rolling process is lower (58.3%), and many shear bands are formed in the coarse cold‐rolled sheet, which leads to the formation of strong Goss and cube texture after recrystallization annealing. Owing to the high annealing temperature, the average grain size of finished annealed sheet is little different under different cold‐rolling processes, so the mechanical properties and high‐frequency iron loss are basically the same. The iron loss of the secondary cold‐rolled products decreases with an increase in frequency, and the improvement in the iron loss of the high field (1.5 T) becomes larger than that of the low field (1.0 T). Given the high anisotropy index of the Goss texture, the iron loss anisotropy of the secondary cold‐rolled sheet is higher. Considering the magnetic and mechanical properties, the optimum process is the secondary cold rolling with the intermediate annealing temperature of 900 °C.

TERTIARY RECRYSTALLIZATION IN THIN STRIPS OF GRAIN ORIENTED SILICON STEEL PRODUCED BY CROSS SHEAR ROLLING

Strain-induced Refinement and Thermal Stability of a Nanocrystalline Steel Produced by Surface Mechanical Attritiontreatment

TEXTURE DISTRIBUTION AND DEVELOPMENT THROUGH THE THICKNESS AFTER CROSS SHEAR ROLLING OF GRAIN ORIENTED SILICON STEEL

Textures and Magnetic Properties of Grain Oriented Electrical Steel Produced by Cross Shear Rolling

Ultra‐Thin 3.5%Si Steel with Both Magnetic Properties and Mechanical Properties Produced by Different Process Routes of Large‐Scale Production

Experimental investigation and simulation of crystallographic orientations evolution in a cold-rolled ultra-thin grain-oriented silicon steel

Microstructural evolution and magnetic properties in strip cast non-oriented silicon steel produced by warm rolling

Coordinate regulation mechanism of primary recrystallization texture and microstructure of grain-oriented silicon steel

Effect of Secondary Cold Rolling Reduction Rate on Secondary Recrystallization Behavior of CGO Steel

Influence Mechanisms of Cold Rolling Reduction Rate on Microstructure, Texture and Magnetic Properties of Non-Oriented Silicon Steel

Effect of Grain Size Before Cold Rolling on Microstructure, Texture and Magnetic Properties of Ultra-Thin Low-Si Non-oriented Silicon Steel

Microstructure and texture evolution of ultra-thin grain-oriented silicon steel sheet fabricated using strip casting and three-stage cold rolling method

Effect of Reduction Ratio in Secondary Cold-rolling on Microstructure and Texture of V and Ti-contained Grain-oriented Silicon Steel

The origin of {113} grains and their impact on secondary recrystallization in producing ultra-thin grain-oriented electrical steel

Effect of cold-rolling deformation and rare earth yttrium on microstructure and texture of oriented silicon steel

Dependence of recrystallization behavior and magnetic properties on grain size prior to cold rolling in high silicon non-oriented electrical steel

Ultrathin-gauge high silicon non-oriented electrical steel with high permeability and low core loss fabricated by optimized two-stage cold rolling method

Effects of Continuous Rolling and Reversible Rolling on 2.4% Si Non-Oriented Silicon Steel

Microstructure and texture evolution of thin-gauge non-oriented silicon steel with high permeability produced by twin-roll strip casting

Investigation of microstructure and texture as related to primary recrystallization of grain-oriented silicon steel

Roles of Silicon Content and Normalization Temperature on Cold Workability and Recrystallization of High-Grade Non-Oriented Silicon Steel