Abstract:International Journal of Modern Physics B, Ahead of Print. This research focuses on the sustainable optimization of the milling process for Titanium Alloy Ti-6Al-4V using Minimum Quantity Lubrication (MQL) assistance. This experimental research investigates the effects of cutting parameters and lubrication conditions on the surface roughness ([math]) and flank wear ([math]) in the milling process of Titanium Alloy Ti-6Al-4V. The study aims to evaluate the influence of cutting speed ([math]), feed rate ([math]) and depth of cut ([math]) on the selected machining performance indicators. The experiments were carried out using a DMG Mori Seiki DMU50 CNC center, and the workpiece samples were measured at [math]. Three different lubrication conditions were employed, including dry machining, conventional flood cooling and Minimum Quantity Lubrication (MQL) using peanut oil. The cutting parameters were varied based on a Taguchi L9 orthogonal array design to explore the main effects of each parameter on [math] and [math]. The results reveal that cutting speed ([math]) has the most significant influence on surface roughness, followed by feed rate ([math]), while the impact of depth of cut ([math] is negligible in comparison. Conversely, the coolant mode has the most significant impact on flank wear ([math]), followed by feed rate ([math]) and depth of cut ([math]), while the influence of cutting speed ([math] is relatively minor. Under the same cutting parameters, transitioning from dry machining to MQL led to a sharp decrease in [math] from 170 to 100[math][math]m, and it increased to approximately 145[math][math]m when switching to flood cooling. Additionally, increasing the feed rate from 0.02 to 0.06[math]mm/tooth reduced [math] from around 135 to 120[math][math]m, but it significantly rose to approximately 165[math][math]m when the feed rate was further increased. Furthermore, the application of MQL with peanut oil as a lubricant and coolant demonstrated improvements in surface finish and reduced tool wear compared to dry and conventional flood cooling. The MQL approach led to better machining performance with lower [math] and [math] values. Overall, this study provides valuable insights into the effects of cutting parameters and lubrication conditions on surface roughness and flank wear in the milling process of Titanium Alloy Ti-6Al-4V. The findings offer practical guidelines for optimizing machining conditions to achieve desired surface quality and extend tool life while considering the environmental benefits of employing MQL in the manufacturing process.

Investigation on Surface Grinding of Ti-6Al-4V Using Minimum Quantity Lubrication

Investigation on Surface Grinding of Ti-6Al-4V Using Minimum Quantity Lubrication

Investigation of Grinding Ti-6al-4v under Minimum Quantity Lubrication (mql) Condition

Analysis of Surface Integrity for MQL in Grinding

Experimental Study on Micro-Milling of Ti6Al4V with Minimum Quantity Lubrication

Investigation Of Cutting Force And Temperature Of End-Milling Ti-6al-4v With Different Minimum Quantity Lubrication (Mql) Parameters

Influence of Minimum Quantity Lubrication Parameters on Tool Wear and Surface Roughness in Milling of Forged Steel

Selection of Minimum Quantity Lubrication (MQL) Parameters in Milling of Ti-6Al-4V

Grindability Evaluation of Ultrasonic Assisted Grinding of Silicon Nitride Ceramic Using Minimum Quantity Lubrication Based SiO2 Nanofluid

Grinding with minimum quantity lubrication: a comparative assessment

The Influence of the Depth of Grinding on the Condition of the Surface Layer of 20MnCr5 Steel Ground with the Minimum Quantity Lubrication (MQL) Method

Investigation of friction in end-milling of Ti-6Al-4V under different green cutting conditions

Friction in Turning Titanium Alloy Ti-6Al-1.5Cr-2.5Mo-0.5Fe-0.3Si under Minimum Quantity Lubrication (MQL) Condition

Specific Energy and G Ratio of Grinding Cemented Carbide under Different Cooling and Lubrication Conditions

Performances of Al 2 O 3 /sic Hybrid Nanofluids in Minimum-Quantity Lubrication Grinding

The Effects of Minimum Quantity Lubrication (MQL) on Machining Force, Temperature, and Residual Stress

Processing Characteristics of Vegetable Oil-based Nanofluid MQL for Grinding Different Workpiece Materials

Towards sustainable manufacturing: Multiple optimization of surface roughness [math], flank wear [math] in MQL-assisted milling of Titanium Alloy Ti-6Al-4V

Evaluation of minimum quantity lubrication grinding with nano-particles and recent related patents

Study on the grinding surface quality of CNTs/2009AL composite material based on minimum quantity lubrication

Effect of Minimum Quantity of Lubricant on Carbide Tools and Surface Integrity in the Machining of Titanium Aluminides