Abstract:International Journal of Modern Physics B, Ahead of Print. This research focuses on the sustainable optimization of the milling process for Titanium Alloy Ti-6Al-4V using Minimum Quantity Lubrication (MQL) assistance. This experimental research investigates the effects of cutting parameters and lubrication conditions on the surface roughness ([math]) and flank wear ([math]) in the milling process of Titanium Alloy Ti-6Al-4V. The study aims to evaluate the influence of cutting speed ([math]), feed rate ([math]) and depth of cut ([math]) on the selected machining performance indicators. The experiments were carried out using a DMG Mori Seiki DMU50 CNC center, and the workpiece samples were measured at [math]. Three different lubrication conditions were employed, including dry machining, conventional flood cooling and Minimum Quantity Lubrication (MQL) using peanut oil. The cutting parameters were varied based on a Taguchi L9 orthogonal array design to explore the main effects of each parameter on [math] and [math]. The results reveal that cutting speed ([math]) has the most significant influence on surface roughness, followed by feed rate ([math]), while the impact of depth of cut ([math] is negligible in comparison. Conversely, the coolant mode has the most significant impact on flank wear ([math]), followed by feed rate ([math]) and depth of cut ([math]), while the influence of cutting speed ([math] is relatively minor. Under the same cutting parameters, transitioning from dry machining to MQL led to a sharp decrease in [math] from 170 to 100[math][math]m, and it increased to approximately 145[math][math]m when switching to flood cooling. Additionally, increasing the feed rate from 0.02 to 0.06[math]mm/tooth reduced [math] from around 135 to 120[math][math]m, but it significantly rose to approximately 165[math][math]m when the feed rate was further increased. Furthermore, the application of MQL with peanut oil as a lubricant and coolant demonstrated improvements in surface finish and reduced tool wear compared to dry and conventional flood cooling. The MQL approach led to better machining performance with lower [math] and [math] values. Overall, this study provides valuable insights into the effects of cutting parameters and lubrication conditions on surface roughness and flank wear in the milling process of Titanium Alloy Ti-6Al-4V. The findings offer practical guidelines for optimizing machining conditions to achieve desired surface quality and extend tool life while considering the environmental benefits of employing MQL in the manufacturing process.

Friction in Turning Titanium Alloy Ti-6Al-1.5Cr-2.5Mo-0.5Fe-0.3Si under Minimum Quantity Lubrication (MQL) Condition

Investigation of the Effects of Cutting Fluid Application with Minimum Quantity Lubrication (MQL) Method on the Machinability of Pure Titanium

Effect of Minimum Quantity of Lubricant on Carbide Tools and Surface Integrity in the Machining of Titanium Aluminides

Tribology of enhanced turning using biolubricants: A comparative assessment

The machinability of titanium alloy thin-wall parts in cooling minimum quantity lubrication (CMQL) environments

Tribology and machinability performance of hybrid Al2O3 -MWCNTs nanofluids-assisted MQL for milling Ti-6Al-4 V

Towards sustainable manufacturing: Multiple optimization of surface roughness [math], flank wear [math] in MQL-assisted milling of Titanium Alloy Ti-6Al-4V

Machinability Assessment of Hybrid Nano Cutting Oil for Minimum Quantity Lubrication (MQL) in Hard Turning of 90CrSi Steel

Minimal quantity cooling lubrication in turning of Ti6Al4V: Influence on surface roughness, cutting force and tool wear

Economic analysis of eco-friendly lubrication strategies for the machining of Ti48Al2Cr2Nb aluminide

Research on Tool Wear and Machining Characteristics of TC6 Titanium Alloy with Cryogenic Minimum Quantity Lubrication (CMQL) Technology

Machining characteristics of Ti6Al4V alloy in laser-assisted machining under minimum quantity lubricant

Analytical Modelling of Cutting Force in End-Milling with Minimum Quantity Lubrication

Machining grade 4 titanium alloy by minimum quantity lubrication for enhanced sustainable manufacturing

Cooling/Lubrication Performance of Dry and Supercritical CO2-Based Minimum Quantity Lubrication in Peripheral Milling Ti-6Al-4V

Effects of the physicochemical properties of different nanoparticles on lubrication performance and experimental evaluation in the NMQL milling of Ti–6Al–4V

Performance and Life Cycle Analysis of Soybean Oil-Based Minimum Quantity Lubrication in Machining of Ti6Al4V

Investigation of the effect of minimum quantity lubrication and Ranque–Hilsch vortex tube cooling on cutting forces, surface roughness and cutting zone temperature in turning Al 6082 T4 alloy

A novel activated sticking-sliding friction model along tool-chip interface and mechanism analysis in high-speed machining of Ti6Al4V

Comparative performance studies of turning 4140 steel with TiC/TiCN/TiN-coated carbide inserts using MQL, flooding with vegetable cutting fluids, and dry machining

Influence of Lubricant Environment on Machined Surface Quality in Single-Point Diamond Turning of Ferrous Metal