Abstract:Functional gradient materials (FGM), with their composition gradually varied in different positions, have attracted much attention for research and development during the years. Normally there are two types of functional gradient materials: one without the formation of intermetallics which is easier for fabrication due to less scientific and technological challenge; the other one with the formation of intermetallics in some part of the gradient changed composition range such as Ti-Al, Ti-Fe, Ni-Al gradient materials, which still exists big challenge on intermetallic, resulting in high brittleness and unavailability.Laser deposition is a competitive candidate for FGM due to its capability on accurate composition and precise dimension control. According to an aeronautical application requirement to gradually change the composition from Ti6Al4V to 316L, this paper reports on laser deposition of Ti6Al4V to 316L gradient composition structure. A big challenge is the formation of the TiFe intermetallic especially near the composition of Ti50Fe50, which results in very high cracking tendency. Many efforts have been made to optimize the Ti-Fe composition ratio, the deposition process and the deposition parameters, not a single Ti6Al4V-316L composition gradient structure was successful due to the formation of the very brittle TiFe and TiFe2 intermetallics. This indicates that it is almost impossible to direct deposit Ti6Al4V to 316L without cracking and separation. We used Inconel 625 powder as an interlayer between the Ti6Al4V and the 316L, thus a sound Ti6Al4V-316L composition gradient structure was successfully achieved by laser deposition. The brittle TiFe and TiFe2 intermetallics were replaced by a series of phase evolutions: α+β → β+Ti2Ni→Ti2Ni+TiNi→TiNi→TiNi+TiNi3→Ni3Fe→ Ni2Fe3→γFe. The brittleness was dramatically decreased or diluted and crack-free composition gradient structure was available. The gradient structure was further analyzed on hardness, microstructural evolution, the Young's modulus and Poisson's ratio.

Microstructure and Mechanical Properties of a Novel Functionally Graded Material from Ti6Al4V to Inconel 625 Fabricated by Dual Wire + Arc Additive Manufacturing

Fabrication and characterization of stainless steel 308 L / Inconel 625 functionally graded material with continuous change in composition by dual-wire arc additive manufacturing

Dual-Wire Plasma Arc Additively Manufactured SS 316L-Inconel 625 Functionally Graded Material: Microstructure Evolution and Mechanical Properties

Microstructure and Mechanical Properties of Ti60-Ti2alnb Functionally Graded Materials Fabricated by Laser Directed Energy Deposition

Additive manufacturing of a functionally graded material from Ti-6Al-4V to Invar: Experimental characterization and thermodynamic calculations

A functionally graded material design from stainless steel to Ni-based superalloy by laser metal deposition coupled with thermodynamic prediction

Influence of composition gradient variation on the microstructure and mechanical properties of 316 L/Inconel718 functionally graded material fabricated by laser additive manufacturing

Research on the microstructure and mechanical properties of functional gradient materials of TC4/TC11 titanium alloys for wire arc additive manufacturing with different transitional forms

Deposition of Functionally Graded Material Fabricated by Robot Plasma Arc Welding

A functionally graded material from stainless steel 304 to Fe–40Al fabricated by dual wire arc additive manufacturing

Microstructural Features and Mechanical Integrity of Wire Arc Additive Manufactured SS321/Inconel 625 Functionally Gradient Material

Microstructural and mechanical properties examination of SS316L-Cu functionally graded material fabricated by wire arc additive manufacturing

Effect of in-situ cooling during pressure and frictional deformation on mechanical and metallurgical properties of Ni-based functionally graded material developed by wire arc additive manufacturing

Characterization of Functionally Graded Material (Stainless Steel 347/308L) Fabricated through Wire and Arc Additive Manufacturing: Microstructure and Mechanical Perspectives

Investigation on dual wire TIG Arc additive manufacturing of IN625 and SS316L FGM for continuous gradient and sandwich structures

Study on Optimization Strategy for the Composition Transition Gradient in SS 316L/Inconel 625 Functionally Graded Materials

Laser Deposition of Ti6Al4V-316L Composition Gradient Structure: Challenge on Intermetallics

Fabrication of functionally graded materials from a single material by selective evaporation in electron beam powder bed fusion

Preparation and investigation of microstructure and wear properties of functionally graded materials of Aluminum-Nickel alloys

Additive manufacturing of titanium alloys with enhanced strength and uniform ductility via multi-element alloying

Microstructure and Mechanical Properties of P21-STS316L Functionally Graded Material Manufactured by Direct Energy Deposition 3D Print