Electrochemical Properties of LiNi1/3Mn1/3Co1/3O2 Synthesized by Co-precipitation Method

Xiaoyu Zhang,Francois Gendron,Alain Mauger,Lu Qi,Henri Groult,Laurent Perrigaud,Christian M. Julien

DOI: https://doi.org/10.1149/ma2009-02/8/611

2009-01-01

ECS Meeting Abstracts

Abstract:Abstract not Available.

What problem does this paper attempt to address?

Cathode Materials of Li_xCo_(0.8)Ni_(0.2)O_2 for Lithium-ion Battery

Yi Zhu

2001-01-01

Journal of Functional Biomaterials

Abstract:Li x Co 0.8 Ni 0.2 O 2, as the cathode materials for lithium-ion battery, were prepared from the precursors, Co 0.8 Ni 0.2 (OH) 2, which were synthesized by the controlled crystallization technology. The experiments of energy diffraction spectroscopy showed that the elements of Co and Ni were distributed uniformly in the active materials. Because the elements of Co and Ni have been distributed uniformly in the M layer of M(OH) 2 during the controlled crystallization process, the long-term calcining process was avoided, when the recomposing process of diffusion happened in the common solid solutions. The microphotographs of SEM indicated the change of microcosmic morphology. The results of XRD proved that the Li x Co 0.8 Ni 0.2 O 2 were single phase with α-NaFeO 2 layered structure, and have no other phases. The crystal lattices of a and c underwent a process from small to big and then to small, and c/a underwent a process from big to small and then to big.
Synthesis and Characterization of LiNi1/3Mn1/3Co1/3O2 by Wet-Chemical Method

Xiaoyu Zhang,A. Mauger,Qi Lu,H. Groult,L. Perrigaud,F. Gendron,C. M. Julien

DOI: https://doi.org/10.1016/j.electacta.2010.06.040

2008-01-01

Abstract:A series of LiNi1/3Mn1/3Co1/3O2 samples with α-NaFeO2 structure were synthesized using tartaric acid as a chelating agent by wet chemical method. Different acid to metal-ion ratios R have been used to investigate the effect of this parameter on the physical and electrochemical properties. The cationic mixing (Ni on the 3a Li sites) have been evaluated by Rietveld refinement and magnetic measurements We determined that the LiNi1/3Mn1/3Co1/3O2 sintered at 900 {degree sign}C for 15 h with an acid to metal ion ratio R=2 was the optimum condition for this synthesis. For this optimized sample, only 1.26% of nickel-ions occupied the 3a Wyckoff site of the lithium-ion sublattice. This material delivered an initial discharge capacity of 172 mAh/g and displayed Coulomb efficiency of 94%.
A Deflagration Method to Synthesize LiNi1/3Co1/3Mn1/3O2 Cathode Materials for Li-ion Batteries

Jiebin Li,Lilong Xiong,Youlong Xu

DOI: https://doi.org/10.1149/ma2009-02/5/282

2009-01-01

ECS Meeting Abstracts

Abstract:Abstract not Available.
Electrode Kinetic of Li(Ni1/3Co1/3Mn1/3) O2 Cathode Material for Lithium Ion Battery

LIU Ling,GUAN Chang,ZHANG Nai-qing,SUN Ke-ning

2012-01-01

Abstract:The compound of Li(Ni1/3Co1/3Mn1/3)O2 was synthesized by co-precipitation method.Its electrode kinetic was investigated by cyclic voltammety(CV) and electrochemical impedance spectroscopy(EIS).The results of CV showed that there was no John-teller effect and reaction between electrode material and electrolyte in the Li(Ni1/3Co1/3Mn1/3)O2.The results of EIS showed that the charge transfer resistance Rct was decreased when the voltage increased and increased when the cycling number increased.
Surface Analysis of the Lithium-Rich Cathode Material Li1.2Mn0.54Co0.13Ni0.13NaxO2 by Advanced Electron Microscopy

Wei HUANG,Chun-Yang WU,Yue-Wu ZENG,Chuan-Hong JIN,Ze ZHANG

DOI: https://doi.org/10.3866/pku.whxb201605164

2016-01-01

Acta Physico-Chimica Sinica

Abstract:In this work, Li1.2Mn0.54Co0.13Ni0.13NaxO2 was prepared via an ion-exchange process combined with a solid-state reaction. Aberration-corrected scanning transmission electron microscopy (STEM), energy dispersive X-ray spectroscopy (EDS), and electron energy loss spectroscopy (EELS) were all used to study the surface structure and chemical distribution of the resulting material. Nickel (Ni) was found to be enriched at the surface in regions perpendicular to the lithium diffusion channels (that is, the (200) surfaces) and also exhibited a tendency to diffuse into the lithium (Li) layers, generating a Fm3m rocksalt phase. In contrast, cobalt (Co) segregated along the transition metal (TM) layers of the (001) and (200) surfaces. The results of aging trials demonstrated that Co-enriched layers lead to surface structure instability, as evidenced by the formation of a large number of antisite defects (Li-TM) and rocksalt phase structures at the (001) surface during aging.
Synthesis of cathode material LiNi_(1/3)Co_(1/3)Mn_(1/3)O_2 and its electrochemical performances

HU Xue-shan,LIU Xing-quan

2006-01-01

Abstract:The lithium-nickel-cobalt-manganese complex oxide LiNi1/3Co1/3Mn1/3O2 was firstly successfully prepared by rheolo- gical phase reaction method. The effect of Li/(Ni+Co+Mn) ratios, calcination temperature and calcination time on performances of LiNi1/3Co1/3Mn1/3O2 were studied. Based on the optimized conditions, LiNi1/3Co1/3Mn1/3O2 cathode material was readily synthesized. The X-ray diffraction patterns show that the structure of precursor sintered beforehand is similar to that of LiNi1/3Co1/3Mn1/3O2.The SEM results reveal that the particle size of LiNi1/3Co1/3Mn1/3O2 is smaller than 1mm.The charge-discharge testing results demonstrate that the LiNi1/3Co1/3Mn1/3O2 compound has better electrochemical properties. The initial discharge specific capacity reached 146.30 mAh/g with a discharge current density of 0.20 mA/cm2 and the discharge specific capacity maintained 136.00 mAh/g after twenty cycles with the same discharge current density.
Diffusion of Li+ in LiNi1/3Mn1/3Co1/3O2

Xiaoyu Zhang,Alain Mauger,Qi Lu,Weijun Jiang,Henri Groult,Christian M. Julien

DOI: https://doi.org/10.1149/ma2011-01/11/564

2011-01-01

ECS Meeting Abstracts

Abstract:Abstract not Available.
Evaluation of the Cation Mixing in LiNi1/3Mn1/3Co1/3O2 Compound

Xiaoyu Zhang,Francois Gendron,Alain Mauger,Lu Qi,Christian M. Julien

DOI: https://doi.org/10.1149/ma2009-02/7/471

2009-01-01

ECS Meeting Abstracts

Abstract:Abstract not Available.
Studies on the Low-Heating Solid-State Reaction Method to Synthesize Lini1/3co1/3mn1/3o2 Cathode Materials

Jingjing Liu,Weihua Qiu,Lingyan Yu,Guohua Zhang,Hailei Zhao,Tao Li

DOI: https://doi.org/10.1016/j.jpowsour.2007.06.236

IF: 9.2

2007-01-01

Journal of Power Sources

Abstract:The low-heating solid-state method has been adopted to synthesize LiNi1/3Co1/3Mn1/3O2 materials. The final product, with homogeneous phase and smooth crystals indicated by XRD and SEM results, can be synthesized at 700°C, much lower than the synthesis temperatures of co-precipitation method. The reaction process and microstructure of precursor has been investigated by IR spectrum. By comparative studies with the mixture of CH3COOLi and (Ni, Co, Mn)(C2O4), it is testified that the precursor is homogeneous, rather than a mixture. The decomposition process and the reaction energy have been studied to investigate the reaction mechanism of the precursor when heated at high temperature. The as-synthesized LiNi1/3Co1/3Mn1/3O2 exhibits excellent electrochemical properties, exhibiting initial specific capacity of 167mAhg−1 with stable cyclic performance.
Structural and Electrochemical Properties of LiNi1/3Mn1/3Co1/3O2 Cathode Material upon Aging in Humid Atmosphere

Xiaoyu Zhang,Francois Gendron,A. Mauger,Qi Lu,Christian M. Julien

DOI: https://doi.org/10.1149/ma2010-03/1/551

2010-01-01

ECS Meeting Abstracts

Abstract:Abstract not Available.
Structure, Electrochemical Properties, and Thermal Stability Studies of Li[Ni[sub 0.2]co[sub 0.6]mn[sub 0.2]]o[sub 2]

Jun Jiang,K. W. Eberman,L. J. Krause,J. R. Dahn

DOI: https://doi.org/10.1149/1.1990532

IF: 3.9

2005-01-01

Journal of The Electrochemical Society

Abstract:Two samples were synthesized by firing coprecipitate mixed with either LiOH or . Another two samples were made from coprecipitate mixed with and LiOH or . All samples were single phase by X-ray diffraction. The structure and electrochemical properties of the synthesized samples were compared and the reactivity of the four charged samples with electrolyte was examined using accelerating rate calorimetry. All four charged samples show less reactivity than in ethylene carbonate/diethyl carbonate solvent or in -based electrolyte. However, synthesized from mixed with LiOH or shows higher thermal stability than samples made from coprecipitate mixed with and LiOH or , even though the particle size of the latter materials is larger. The reasons for this surprising result are explained. Because the safety of materials is strongly dependent on , near , the safest materials are those with the most homogeneously mixed cations.
Aging of LiNi1/3Mn1/3Co1/3O2 as Cathode Material for Li-ion Batteries

Xiaoyu Zhang,Francois Gendron,Alain Mauger,Lu Qi,Christian Julien

DOI: https://doi.org/10.1149/ma2009-02/7/436

2009-01-01

ECS Meeting Abstracts

Abstract:Abstract not Available.
Effects On Wet-Coated 0.5Li2MnO3·0.5LiNi1/3Co1/3Mn1/3O2 Cathode Material for Li-Ion Batteries

Jianling, Li

DOI: https://doi.org/10.1149/ma2013-02/14/1083

2013-01-01

ECS Meeting Abstracts

Abstract:Abstract not Available.
Preparation of layered LiNi1/3Co1/3-xLaxMn1/3O2 as cathode material by oxalate co-precipitation method

Chuan-yue HU,Jun GUO,Xing-yan WANG,Tao YI,Yong DU

DOI: https://doi.org/10.3969/j.issn.1002-087X.2010.12.005

2010-01-01

Abstract:The layered Li[Ni1/3Co1/3-xLaxMn1/3]O2(0<x<1) was synthesized by oxalate co-precipitation method.The influence of La-dopants on the structural and electrochemical properties of the Li[Ni1/3Co1/3Mn1/3]O2 materials was studied.The results show that LiNi1/3Co1/3-0.04La0.04Mn1/3O2 deliveres a better layer-structural and good electrochemical properties.The XRD analysis indicates that the presently synthesized Li[Ni1/3Co1/3-0.04Mn1/3]O2 has a hexagonal layered-structure.The initial specific discharge capacity of the Li[Ni1/3Co1/3-0.04Mn1/3]O2 positive-electrode material is determined to be 147.56 mAh/g using a Li/Li[Ni1/3Co1/3Mn1/3]O2 cell operated at 0.1 C ratio in voltages of 2.8-4.2 V.The discharge capacity is 141.7 mAh·g-1 after 20 cycles with 0.2 C ratio and 20 cycles with 0.5 C ratio.The spherical particle size distribution of the Li[Ni1/3Co1/3-0.04Mn1/3]O2 powder was observed via scanning electron microscopy.The average particle size is measured to be about 1.2 mm in diameter.
Synthesis of LiNi0.6Co0.2Mn0.2O2 Cathode Material by a Carbonate Co-Precipitation Method and Its Electrochemical Characterization

Yao Zhang,Hui Cao,Jian Zhang,Baojia Xia

DOI: https://doi.org/10.1016/j.ssi.2006.09.008

IF: 3.699

2006-01-01

Solid State Ionics

Abstract:Using Na2CO3 and Me(NO3)(2) (Me=Ni, Co and Mn) as starting materials, the precursor of LiNi0.6Co0.2Mn0.2O2 cathode material for lithium rechargeable batteries has been synthesized by carbonate co-precipitation. The precursor was mixed with Li2CO3 and heated in air. Thermogravimetric analysis (TG-DTA), laser particle size analysis, X-ray diffraction (XRD) and electron scanning microscopy (SEM) were employed to study the reaction process and the structures of the powders. The D-50 of precursor was 2.509 mu m and the distribution was relatively narrow. The optimum calcination temperature was 850-900 degrees C. Galvanostatic cell cycling and cyclic voltammetry were also used to evaluate the electrochemical properties. The initial discharge capacity for the powders calcined at 900 degrees C was about 180 mA h/g at room temperature when cycled between 2.8 and 4.3 V at 0.2 C rate. (c) 2006 Elsevier B.V. All rights reserved.
Synthesis and Electrochemical Characterization of Li[Ni_xCo_(1-2x)Mn_x]O_2 Prepared by Spray Pyrolysis

LIU Zhimin,LIU Yexiang,HU Guorong,DENG Xinrong,GAO Xuguang,XIAO Zhengwei

2008-01-01

Abstract:The layered Li[Ni_xCo_(1-2x)Mn_x]O_2(x=0.25、0.33、0.4,0.5) materials are synthesized by spray pyrolysis methods,and characterized by means of SEM,XRD,ICP,charge/discharge tests etc techniques.The test results show that spherical Li[Ni_xCo_(1-2x)Mn_x]O_2 is prepared by spray pyrolysis and the chemical content of samples is well controlled.As the Co content increases,the lattice parameters of Li[Ni_xCo_(1-2x)Mn_x]O_2 decreased in a axis and c axis,but I_(003)/I_(104) increased.The result indicate that the Co content can stabilify the layered structure,and reduce structural disorder between Ni~(2+) and Li~+.The results of the electrochemical tests on 2025 coin-cells show high Co content samples have a higher specific discharge capacity,better rate performance and cycling characteristic.
Preparation and Electrochemical Properties of LiNi2/3Co1/6Mn1/6O2 Cathode Material for Lithium-Ion Batteries

Meijie Zhu,Jiangang Li,Zhibei Liu,Li Wang,Yuqiong Kang,Zhaohan Dang,Jiasen Yan,Xiangming He

DOI: https://doi.org/10.3390/ma14071766

IF: 3.4

2021-01-01

Materials

Abstract:The cathode material LiNi2/3Co1/6Mn1/6O2 with excellent electrochemical performance was prepared successfully by a rheological phase method. The materials obtained were characterized by X-ray diffraction, scanning electron microscopy, electrochemical impedance spectroscopy and charge-discharge tests. The results showed that both calcination temperatures and atmosphere are very important factors affecting the structure and electrochemical performance of LiNi2/3Co1/6Mn1/6O2 material. The sample calcinated at 800 °C under O2 atmosphere displayed well-crystallized particle morphology, a highly ordered layered structure with low defects, and excellent electrochemical performance. In the voltage range of 2.8–4.3 V, it delivered capacity of 188.9 mAh g−1 at 0.2 C and 130.4 mAh g−1 at 5 C, respectively. The capacity retention also reached 93.9% after 50 cycles at 0.5 C. All the results suggest that LiNi2/3Co1/6Mn1/6O2 is a promising cathode material for lithium-ion batteries.
Characterizations on the Structural and Electrochemical Properties of LiNi1/3Mn1/3Co1/3O2 Prepared by a Wet-Chemical Process

X. Li,Y. J. Wei,H. Ehrenberg,F. Du,C. Z. Wang,G. Chen

DOI: https://doi.org/10.1016/j.ssi.2008.01.048

IF: 3.699

2008-01-01

Solid State Ionics

Abstract:LiNi1/3Mn1/3Co1/3O2 compounds were prepared at 700 (sample-A) and 900 degrees C (sample-B) by a simple wet-chemical process. X-ray diffraction showed the sample-A had a larger Li/Ni site exchange (9.9%) than that of the sample-B (4.4%). Raman scattering analysis suggests strong structural disorder within the octahedral [MO6] units due to different masses and bonding of the M-O bonds, as well as the Li/Ni site exchange in the crystals. The weakening of the E-g band was correlated with the Li/Ni site exchange. XPS analysis indicates that a lower annealing temperature than 900 'C leads to the formation of oxygen deficient LiNi1/3Mn1/3Co1/3O2-delta. The electrochemical properties of the materials were investigated by charge-discharge experiments and electrochemical impedance spectroscopy. The drastic capacity fading of the sample-A was attributed to its structural properties. The sample-B showed satisfying cycling performance. But the capacity fading in the potential region of 2.5-4.6 V was larger than that in 2.5-4.4 V, which was attributed to the large charge transfer resistance at potentials above 4.4 V. (C) 2008 Elsevier B.V. All rights reserved.
Characterization of Wet-Chemistry Synthesized LiNi_(0.8)Co_(0.2)O_2

ZHONG Yao-dong,ZHANG Ya-fei,QIANG Ying-huai,SUN Zhi,JIANG Li

2009-01-01

Abstract:LiNi_(0.8)Co_(0.2)O_2 is one of the potential cathode material for Li-ion battery.The materials with homogeneous phase,narrow distribution of particle size and enhanced performance of Li-ion battery can be achieved by wet-chemistry.Coprecipitation and particulate sol-gel(PSG) were used to synthesize LiNi_(0.8)Co_(0.2)O_2.The precursor β-(Ni,Co)(OH_2) was firstly prepared by coprecipitation method,then it was calcined with lithium in the stoichiometric amount to form LiNi_(0.8)Co_(0.2)O_2.In PSG,the gel was formed when an esterification happened.Both nickel and cobalt were reduced as metals,while lithium carbonate was remained.LiNi_(0.8)Co_(0.2)O_2 was also produced after calcining.In PSG,the synthesized materials were examined by using Infrared spectroscopy(IR),X-ray diffratometry(XRD),Rietveld refinement,electrochemical impedance spectroscopy(EIS) and cycleability measurements.The LiNi_(0.8)Co_(0.2)O_2 produced by both methods is well-crystallized,which is confirmed through XRD.However,all the results of Rietveld refinement,EIS and cycleability measurements indicate that the PSG method is better by which the product has better layered structure,smaller charge transfer resistance and better cycleability.
Investigation on Structure and Electrochemical Properties of Li[Ni1/3Co1/3Mn1/3]O2 for Lithium Ion Batteries

Xiu Juan Shi,Yong Ping Zheng,Fei Yu Kang,Xin Lu Li,Wan Ci Shen

DOI: https://doi.org/10.4028/www.scientific.net/KEM.336-338.455

2007-01-01

Key Engineering Materials

Abstract:Cathode material Li[Ni1/3Co1/3Mn1/3]O-2 for lithium-ion batteries with layered hexagonal structure was successfully synthesized in sol-gel way. The influences of calcination temperature (from 700 degrees to 1000 degrees C) on the structure and electrochemical behaviors of Li[Ni1/3Co1/3Mn1/3]O-2 were extensively investigated. The results of XRD show that all samples are isostructural with alpha-NaFeO2 with a space group R-3m. XPS analysis shows that the oxidation states of Co and Mn were Co3+ and Mn4+ respectively, while Ni exists as Ni2+ and Ni3+. The charge-discharge experiments show that the sample calcined at 850 degrees C delivers 194.8mAh/g in the first cycle at C/5 rate in 2.5-4.3V potential range.

Electrochemical Properties of LiNi<sub>1/3</sub>Mn<sub>1/3</sub>Co<sub>1/3</sub>O<sub>2</sub> Synthesized by Co-precipitation Method

Cathode Materials of Li_xCo_(0.8)Ni_(0.2)O_2 for Lithium-ion Battery

Synthesis and Characterization of LiNi1/3Mn1/3Co1/3O2 by Wet-Chemical Method

A Deflagration Method to Synthesize LiNi<sub>1/3</sub>Co<sub>1/3</sub>Mn<sub>1/3</sub>O<sub>2</sub> Cathode Materials for Li-ion Batteries

Electrode Kinetic of Li(Ni1/3Co1/3Mn1/3) O2 Cathode Material for Lithium Ion Battery

Surface Analysis of the Lithium-Rich Cathode Material Li<sub>1.2</sub>Mn<sub>0.54</sub>Co<sub>0.13</sub>Ni<sub>0.13</sub>Na<sub><i>x</i></sub>O<sub>2</sub> by Advanced Electron Microscopy

Synthesis of cathode material LiNi_(1/3)Co_(1/3)Mn_(1/3)O_2 and its electrochemical performances

Diffusion of Li<sup>+</sup> in LiNi<sub>1/3</sub>Mn<sub>1/3</sub>Co<sub>1/3</sub>O<sub>2</sub>

Evaluation of the Cation Mixing in LiNi<sub>1/3</sub>Mn<sub>1/3</sub>Co<sub>1/3</sub>O<sub>2</sub> Compound

Studies on the Low-Heating Solid-State Reaction Method to Synthesize Lini1/3co1/3mn1/3o2 Cathode Materials

Structural and Electrochemical Properties of LiNi<sub>1/3</sub>Mn<sub>1/3</sub>Co<sub>1/3</sub>O<sub>2</sub> Cathode Material upon Aging in Humid Atmosphere

Structure, Electrochemical Properties, and Thermal Stability Studies of Li[Ni[sub 0.2]co[sub 0.6]mn[sub 0.2]]o[sub 2]

Aging of LiNi<sub>1/3</sub>Mn<sub>1/3</sub>Co<sub>1/3</sub>O<sub>2</sub> as Cathode Material for Li-ion Batteries

Effects On Wet-Coated 0.5Li<sub>2</sub>MnO<sub>3</sub>·0.5LiNi<sub>1/3</sub>Co<sub>1/3</sub>Mn<sub>1/3</sub>O<sub>2</sub> Cathode Material for Li-Ion Batteries

Preparation of layered LiNi1/3Co1/3-xLaxMn1/3O2 as cathode material by oxalate co-precipitation method

Synthesis of LiNi0.6Co0.2Mn0.2O2 Cathode Material by a Carbonate Co-Precipitation Method and Its Electrochemical Characterization

Synthesis and Electrochemical Characterization of Li[Ni_xCo_(1-2x)Mn_x]O_2 Prepared by Spray Pyrolysis

Preparation and Electrochemical Properties of LiNi<sub>2/3</sub>Co<sub>1/6</sub>Mn<sub>1/6</sub>O<sub>2</sub> Cathode Material for Lithium-Ion Batteries

Characterizations on the Structural and Electrochemical Properties of LiNi1/3Mn1/3Co1/3O2 Prepared by a Wet-Chemical Process

Characterization of Wet-Chemistry Synthesized LiNi_(0.8)Co_(0.2)O_2

Investigation on Structure and Electrochemical Properties of Li[Ni<sub>1/3</sub>Co<sub>1/3</sub>Mn<sub>1/3</sub>]O<sub>2</sub> for Lithium Ion Batteries