Abstract:The bottleneck problems of SiC particles reinforced AlSi10Mg composites (SiC/AlSi10Mg) prepared by traditional casting method, such as composition segregation, interface reaction and coarse microstructure, can be effectively improved by powder metallurgy with lower processing temperature. In this study, the influence of SiC particle size and content on the properties of SiC/AlSi10Mg was systematically analyzed. SiC/AlSi10Mg composites were prepared by planetary ball milling, spark plasma sintering (SPS) and hot extrusion composite preparation process. The obtained composites presents dense microstructure without the formation of interfacial reaction phase. The distribution of micron SiC particles (μm-SiC) in the matrix is relatively uniform, and nano SiC particles (nm-SiC) slightly agglomerates with the increase of the content. The strength of SiC/AlSi10Mg increases with the increase of nm-SiC content, which is mainly attributed to dispersion strengthening, dislocation strengthening and grain refinement strengthening. The strength of SiC/AlSi10Mg hardly changes with the increase of μm-SiC content, but the elongation decreases gradually. The deformation between μm-SiC and AlSi10Mg matrix is not coordinated and μm-SiC cleave the AlSi10Mg matrix. The irregular boundaries of μm-SiC are easy to produce stress concentration during loading, leading to interface cracking or μm-SiC fracture. Therefore, μm-SiC are difficult to play a significant strengthening effect to composites. With the increase of SiC content, the fracture mechanism of composites gradually changes from ductile fracture to brittle fracture in SiC agglomeration region. This study lays a theoretical and experimental foundation for the controllable preparation and performance optimization of high strength and toughness AMCs reinforced by SiC particles.

Preparation and Characterization of SiC/Al2O3 Composites

Experiment and FEM Study on Uniaxial Tensile of SiCp/Al

Investigation of microstructures and mechanical properties of ultrafine SiC reinforced pure Al matrix composites

Effect of Al(OH)<sub>3</sub> Addition on the Properties of SiC/Al<sub>2</sub>O<sub>3</sub> Composite Porous Ceramics

Effect of Al(OH)3 addition on the properties of SiC/Al2O3 composite porous ceramics

Fabrication and Mechanical Properties of Silicon Carbide–aluminum Oxynitride Nanocomposites

Influence of characteristic parameters of SiC reinforcements on mechanical properties of AlSi10Mg matrix composites by powder metallurgy

Microstructure and mechanical properties of SiC-Al2O3 nanocomposite prepared by surface modified SiC nanopowders

Microstructure and Mechanical Properties of Hot-Pressed Al2O3–mullite–ZrO2–SiC Composites

Preparation and Characterization of Al_2O_3-SiC Ceramic Nanocomposites

Microstructure and Mechanical Properties of SiCp/AlCuMgAgCe Composites

Effect of Silicon Addition on Mechanical Properties of Mullite-Sic Composite Refractories

Mechanical properties of Al2O3–SiC–C composites using polycarbosilane as SiC precursor

Preparation and Characterization of Different Surface Modified SiCp Reinforced Al-matrix Composites

Microstructural analysis of SiCp/Al composites

Effects of residual stress and intragranular particles on mechanical properties of hot-pressed Al2O3/SiC ceramic composites

Microstructure and Mechanical Properties of Unidirectional, Laminated Cf/SiC Composites with α-Al2O3 Nanoparticles as Filler

Characterization of a Powder Metallurgy SiC/Cu–Al Composite

Effect of Al2O3 addition on mechanical properties of SiC-platelet/Y-TZP composites

Mechanical Properties and Microstructure of Al<sub>2</sub>O<sub>3</sub>-Ti<sub>3</sub>SiC<sub>2</sub> Ceramic Composites

Effects of SiC contents on the microstructure and mechanical properties of Al4SiC4–SiC ceramic composites