Abstract:The effects of an α-Al2O3 nanoparticle filler in the SiC matrix on the mechanical properties and failure mechanism of the unidirectional, laminated carbon fiber-reinforced SiC composites were investigated in this work. First, α-Al2O3 nanoparticles were added to the carbon fiber bundles using a slurry impregnation method, and then the Cf/SiC composite with an α-Al2O3 nanoparticle filler (Cf/SiC-Al2O3) was fabricated using a precursor infiltration and pyrolysis method. The microstructure of the Cf/SiC-Al2O3 composite showed chemical compatibility between the α-Al2O3 and the pyrolysis SiC. The Cf/SiC-Al2O3 composite with a low porosity of ~6.67% achieved a good flexural strength of 629.3 MPa and a good fracture toughness of 25.2 MPa·m1/2. The interlaminar shear strength of the Cf/SiC-Al2O3 composite was 11.7 MPa. The SiC-Al2O3 matrix also presented a considerable Young’s modulus of 138.2 ± 8.66 GPa and hardness of 10.3 ± 1.03 GPa. Further analysis indicated that the good mechanical properties with the addition of an α-Al2O3 filler were not only related to the dense matrix and the improvement of the mechanical properties of the matrix. They also originated from the thermal residual compressive stress in the SiC matrix close to the α-Al2O3 nanoparticles caused by the thermal expansion mismatch, which could reflect and close the cracks in the matrix. The findings of this study provide more methods for designing new composites exhibiting a good performance.

Mechanical properties of Al2O3–SiC–C composites using polycarbosilane as SiC precursor

Effect of polycarbosilane content on microstructures and mechanical properties of short-carbon-fibre-reinforced SiC composites

Microstructure and Mechanical Properties of Hot-Pressed Al2O3–mullite–ZrO2–SiC Composites

Microstructures of a carbon-fiber-reinforced silicon-carbide composite produced by precursor pyrolysis and hot pressing

Effects of silicon addition on the microstructure and properties of B 4 C–SiC composite prepared with polycarbosilane-coated B 4 C powder

Study on the mechanical properties and microstructure of Al2O3/nano-SiC multiphase ceramics

Microstructure, mechanical and friction-wear properties of SiC-WC composite with Al and C as sintering aids

Effects of SiC contents on the microstructure and mechanical properties of Al4SiC4–SiC ceramic composites

Structure and properties of fine diameter continuous SiC ceramic fiber reinforced Al matrix composites

Fabrication, Microstructure, and Properties of SiC/Al 4 SiC 4 Multiphase Ceramics Via an In-Situ Formed Liquid Phase Sintering

Microstructure and Properties of Hot Pressed Zr2(Al(Si))4C5/SiC Composites

Microstructures of Short-Carbon-Fiber-Reinforced Sic Composites Prepared by Hot-Pressing

The Microstructure and Mechanical Property of Mo(Si, Al)2-SiC Composite Prepared by Infiltrating Melt Aluminum

Effect of SiC Addition on Mechanical Properties of Hot-Pressed Al2O3-GdAlO3 Ceramics with Eutectic Composition

Processing and Mechanical Properties of Multiphase Composites Based on Mo–Si–Al–C System

Fabrication, microstructure, and properties of SiC/Al4SiC4 multiphase ceramics via an in-situ formed liquid phase sintering

Influence of polycarbosilane composition on the properties of SiC/SiC composite fabricated by precursor infiltration and pyrolysis process

Microstructure and Mechanical Properties of Unidirectional, Laminated Cf/SiC Composites with α-Al2O3 Nanoparticles as Filler

Mechanical and Tribological Properties of SiC Whisker‐reinforced SiC Composites Via Oscillatory Pressure Sintering

Effects of residual stress and intragranular particles on mechanical properties of hot-pressed Al2O3/SiC ceramic composites

Effect of Silicon Addition on Mechanical Properties of Mullite-Sic Composite Refractories