Abstract:The bottleneck problems of SiC particles reinforced AlSi10Mg composites (SiC/AlSi10Mg) prepared by traditional casting method, such as composition segregation, interface reaction and coarse microstructure, can be effectively improved by powder metallurgy with lower processing temperature. In this study, the influence of SiC particle size and content on the properties of SiC/AlSi10Mg was systematically analyzed. SiC/AlSi10Mg composites were prepared by planetary ball milling, spark plasma sintering (SPS) and hot extrusion composite preparation process. The obtained composites presents dense microstructure without the formation of interfacial reaction phase. The distribution of micron SiC particles (μm-SiC) in the matrix is relatively uniform, and nano SiC particles (nm-SiC) slightly agglomerates with the increase of the content. The strength of SiC/AlSi10Mg increases with the increase of nm-SiC content, which is mainly attributed to dispersion strengthening, dislocation strengthening and grain refinement strengthening. The strength of SiC/AlSi10Mg hardly changes with the increase of μm-SiC content, but the elongation decreases gradually. The deformation between μm-SiC and AlSi10Mg matrix is not coordinated and μm-SiC cleave the AlSi10Mg matrix. The irregular boundaries of μm-SiC are easy to produce stress concentration during loading, leading to interface cracking or μm-SiC fracture. Therefore, μm-SiC are difficult to play a significant strengthening effect to composites. With the increase of SiC content, the fracture mechanism of composites gradually changes from ductile fracture to brittle fracture in SiC agglomeration region. This study lays a theoretical and experimental foundation for the controllable preparation and performance optimization of high strength and toughness AMCs reinforced by SiC particles.

Microstructure and Mechanical Properties of SiCp/AlCuMgAgCe Composites

Microstructure and Mechanical Properties of SiC_p/AlCuMgAgCe Composites

Experiment and FEM Study on Uniaxial Tensile of SiCp/Al

Microstructure and Mechanical Properties of High Volume SiC_p Reinforement Magnesium Matrix Composites

Microstructural analysis of SiCp/Al composites

Microstructure and Mechanical Properties of High Volume SiC_p/Mg-6Al-0.5Mn Composites

Microstructure and Mechanical Properties of High Volume Fraction SiCp Reinforced Heat Resistant Aluminum Matrix Composites

Microstructure and Mechanical Properties of 45 vol.% SiC p /7075Al Composite

Investigation on the Compressive Property of SiCp/Al Functionally Gradient Materials

Mechanical properties and microscopic analysis of SiCP/Al composites

Microstructure and Mechanical Properties of Sic/Al Nanocomposite

Microstructures and Tensile Properties of Al–Cu Matrix Composites Reinforced with Nano-Sized SiCp Fabricated by Semisolid Stirring Process

Microstructure and Thermal Conduction Property of SiCp/Al- Si Composite with High Reinforcement Content

Microstructures and Tensile Properties of Nano-Sized SiCp/Al-Cu Composites Fabricated by Semisolid Stirring Assisted with Hot Extrusion

Microstructure and Mechanical Properties of Cf+SiC/Al Composites Fabricated by Squeeze Cast

Numerical Simulation of the Mechanical Properties and Fracture of SiCp/6061Al Composite Materials Based on Microstructure

Microstructure and mechanical properties of SiC reinforced AlSi10Mg composites fabricated by laser metal deposition

Investigation of microstructures and mechanical properties of ultrafine SiC reinforced pure Al matrix composites

Influence of characteristic parameters of SiC reinforcements on mechanical properties of AlSi10Mg matrix composites by powder metallurgy

Microstructure Evolution and Mechanical Behaviors of SiCp/CNTs Hybrid Reinforced Al-Si-Cu-Mg Composite by Semi-solid Stir Casting

Processing, Microstructure and Mechanical Properties of SiCp/AZ91 Mg Matrix Composites Fabricated by Squeeze Casting