Abstract:The bottleneck problems of SiC particles reinforced AlSi10Mg composites (SiC/AlSi10Mg) prepared by traditional casting method, such as composition segregation, interface reaction and coarse microstructure, can be effectively improved by powder metallurgy with lower processing temperature. In this study, the influence of SiC particle size and content on the properties of SiC/AlSi10Mg was systematically analyzed. SiC/AlSi10Mg composites were prepared by planetary ball milling, spark plasma sintering (SPS) and hot extrusion composite preparation process. The obtained composites presents dense microstructure without the formation of interfacial reaction phase. The distribution of micron SiC particles (μm-SiC) in the matrix is relatively uniform, and nano SiC particles (nm-SiC) slightly agglomerates with the increase of the content. The strength of SiC/AlSi10Mg increases with the increase of nm-SiC content, which is mainly attributed to dispersion strengthening, dislocation strengthening and grain refinement strengthening. The strength of SiC/AlSi10Mg hardly changes with the increase of μm-SiC content, but the elongation decreases gradually. The deformation between μm-SiC and AlSi10Mg matrix is not coordinated and μm-SiC cleave the AlSi10Mg matrix. The irregular boundaries of μm-SiC are easy to produce stress concentration during loading, leading to interface cracking or μm-SiC fracture. Therefore, μm-SiC are difficult to play a significant strengthening effect to composites. With the increase of SiC content, the fracture mechanism of composites gradually changes from ductile fracture to brittle fracture in SiC agglomeration region. This study lays a theoretical and experimental foundation for the controllable preparation and performance optimization of high strength and toughness AMCs reinforced by SiC particles.

Investigation on the Compressive Property of SiCp/Al Functionally Gradient Materials

Numerical Simulation of the Mechanical Properties and Fracture of SiCp/6061Al Composite Materials Based on Microstructure

Microstructure evolution, property analysis, and interface study of 3%CF-3%SiC-10%SiC functional gradient aluminum matrix composites

Preparation and characterization of Al2O3–Ti3SiC2 composites and its functionally graded materials

Influence of Reinforcement with Multimodal Distribution on Thermophysical Properties and Fracture Behavior in Al-Si/SiC Composites Infiltrated under Super-Gravity Field

Interfacial Regulation and Fracture Mechanism of Al–Si/SiC Composites Infiltrated under Super-Gravity Field

Experimental and Numerical Investigations of Tensile Properties of SiC Particle‐Reinforced Composites

In situ observation of fracture in homogeneous and functionally graded 6061Al/SiCp composites

Influence of characteristic parameters of SiC reinforcements on mechanical properties of AlSi10Mg matrix composites by powder metallurgy

Structure and properties of functionally gradient aluminium alloy 2124/SiC composites

Fabrication and characteristics of plasma facing SiC/C functionally graded composite material

A Novel Functionally Graded Material in the Ti–Si–C System

Regarding the Si Content Associated Micro-Structural Characteristics on the Low Cycle Fatigue Behaviour of Al-Si/SiCp Composite.

Study on the Fabrication and Mechanical Properties of SiC P /sic Gradient Lattice Structure Based on Selective Laser Sintering Technology

Characterization of a Powder Metallurgy SiC/Cu–Al Composite

The dynamic properties of SiCp/Al composites fabricated by spark plasma sintering with powders prepared by mechanical alloying process

Hot extrusion of SiCp/Al-Cu composites: optimizing mechanical properties through microstructural control

Microstructure and mechanical properties of SiC reinforced AlSi10Mg composites fabricated by laser metal deposition

Investigation of the physical and mechanical properties of hot-pressed machinable Si3N4/h-BN composites and FGM

Effect of Silicon Carbide Weight Percentage and Number of Layers on Microstructural and Mechanical Properties of Al7075/SiC Functionally Graded Material

Structure–property relationships of SiC reinforced advanced Al–Zn–Mg–Cu alloy