Abstract:The A15 phase superconductor Nb3Al has been considered as an alternative to Nb3Sn for high field and large scale applications. However, to prepare a stoichiometric Nb3Al with fine grain structures is very difficult. High-energy ball milling is a solid state powder processing technique and is a very useful for preparing Nb-Al alloys (Nb3Al). The effects of ball milling time and annealing temperature on the formation of Nb3Al superconducting phase have been studied. Pure Nb and Al powders with stoichiometric ratio of Nb3Al were mixed and milled, and the charging and milling were performed in an inert atmosphere. Phase formation and structural evolution during high-energy ball milling have been examined by X-ray diffraction. Al disappeared and Nb peaks broadened after about one hour of milling. With increasing milling time, the peaks of Nb became considerably broader and intensities decreased, the Nb-Al solid solution phase was extensive when milled about 3 hours. In order to obtain Nb3Al superconducting phase, a subsequent anneal was required. We have annealed the as-milled powders at 800-900°C for different times to prepared Nb3Al superconducting alloy. The results indicated that Nb3Al with small amount of impurity phase can be obtained on annealing the Nb-Al solid solution phase and the superconducting transition temperature was about 15K, but it is difficult to obtain a homogeneous Nb3Al phase by annealing the amorphous powder.

Formation of 25 Mol % Fe<sub>2</sub>O<sub>3</sub>-Al<sub>2</sub>O<sub>3</sub> Solid Solution by High-Energy Ball Milling

Formation of 25 Mol% Fe2o3-Al2o3 Solid Solution by High-Energy Ball Milling

Microstructural Evolution During High Energy Ball Milling of Fe2o3-Sio2 Powders

Characterization of Nanostructured Alpha-Fe2o3-Sno2 Solid Solutions Prepared by High Energy Ball Milling

Mechanical milling of Fe3O4/SiO2: Formation of an amorphous Fe(II)-Si-O-containing phase

Reversible α-Fe<sub>2</sub>O<sub>3</sub> to Fe<sub>3</sub>O<sub>4</sub> Transformation during Ball Milling

Amorphization in the AlC System by Mechanical Alloying

Formation of Nanocrystalline Fcc Phase by Mechanically Driven Crystallization

High-energy ball milling of Al2O3–TiO2 powders

Mechanical Alloying Process of the Zirconia–8 Mol % Yttria Ceramic Powder

Preparation of Nb3al by High-Energy Ball Milling and Superconductivity

Properties of High-Entropy Fe30Co20Ni20Mn20Al10 Alloy Produced by High-Energy Ball Milling

The research of processing of Zn/Al2O3 composite powders obtained by high energy ball milling of Al-ZnO

Nano-sized amorphous alumina particles obtained by ball milling ZnO and Al powder mixture

Preparation of FeAl (B2) intermetallic powder by ball milling and heat treatment

Solid State Reaction of Al-ZnO Powders by Mechanical Alloying

Synthesis and phase formation mechanism of alpha-Fe2O3 powders by hydrothermal reaction method

Synthesis of SnFe2O4 Nanomaterials Via High Energy Ball Milling of SnO (Stannous) and α-Fe2O3 (Hematite) Solid Precursors

Structure and Thermal Stability of Nanostructured Iron-doped Zirconia Prepared by High-energy Ball Milling

Structural and Magnetic Properties of Ball Milled Copper Ferrite

Preparation and properties of Al2O3/Al-2(1-0.2)Mg0.2Ti(1+0.2)O5 matrix ceramic composite

Formation of 25 Mol % Fe&lt;sub&gt;2&lt;/sub&gt;O&lt;sub&gt;3&lt;/sub&gt;-Al&lt;sub&gt;2&lt;/sub&gt;O&lt;sub&gt;3&lt;/sub&gt; Solid Solution by High-Energy Ball Milling