Abstract:This paper reports a grain regrowth and bifacial passivation strategy to reduce recombination losses for wide‐bandgap perovskite solar cells. As a result, PCEs of 21.9% and 19.9% are achieved for the opaque and semitransparent perovskite solar cells, respectively. Furthermore, a perovskite/silicon 4‐terminal (4‐T) tandem cell with an attractive PCE of 29.8% is realized. The wide‐bandgap perovskite solar cell is a crucial part of perovskite/silicon tandem solar cells, which offer an avenue for surpassing the power conversion efficiency (PCE) limit of single‐junction silicon solar cells. However, the actual efficiency of such tandem solar cells today is diminished by the nonradiative recombination losses in the wide‐bandgap perovskite subcells. Here, this work reports a grain regrowth and bifacial passivation (GRBP) strategy to reduce recombination losses at the grain boundaries and perovskite/charge transport layer interfaces simultaneously. This is achieved by a posttreatment of perovskite films with a mixture of methylammonium thiocyanate (MASCN) and phenethylammonium iodide (PEAI). The MASCN induces the regrowth of perovskite grains and simultaneously facilitates the penetration of PEAI into the hole‐transport‐layer (HTL)/perovskite bottom interface. Thereby, the bulk and interface nonradiative recombination losses are reduced and the open‐circuit voltage in solar cells is considerably increased. PCEs of 21.9% and 19.9% for the 1.65‐eV bandgap opaque and semitransparent perovskite solar cells, respectively, are obtained. The encapsulated semitransparent perovskite solar cells retain their initial efficiency following 500 h of operation under one‐sun illumination in ambient conditions. The perovskite/silicon 4‐terminal (4‐T) tandem cells are fabricated with impressive PCEs 29.8% and 28.5% for 0.049 cm2 and 1 cm2 devices, respectively.

Ultrathin Bifacial Passivated Emitter and Rear Cell with Inverted Pyramid Textures

High-Efficiency Silicon Inverted Pyramid-Based Passivated Emitter and Rear Cells

Inverted Pyramid Morphology Control by Acid Modification and Application for PERC Solar Cells

Improvement of conversion efficiency of multicrystalline silicon solar cells by incorporating reactive ion etching texturing

Improvement of Light Trapping in Bifacial PERC Silicon Solar Cells by Optimizing the Rear Surface Morphology

Small Pyramidal Textured Ultrathin Crystalline Silicon Solar Cells with Double-Layer Passivation.

High Performance Inverted RbCsFAPbI3 Perovskite Solar Cells Based on Interface Engineering and Defects Passivation.

Large-area MACE Si Nano-Inverted-pyramids for PERC Solar Cell Application

Design Investigation on 100 Μm-Thickness Thin Silicon PERC Solar Cells with Assistance of Machine Learning

Multi-layer transparent electrodes for high performance bifacial perovskite solar cells

Improved Bifacial Properties of P‐Type Passivated Emitter and Rear Cell Solar Cells toward High Mass Production Efficiency

Upright Pyramids Vs. Inverted Pyramids Surface Textures: a Comparative Investigation on the Electrical Properties of PERC Solar Cells

Solution of Efficiency Loss in Thinned Silicon PERC Solar Cells

Realization of 13.6% Efficiency on 20 μm Thick Si/Organic Hybrid Heterojunction Solar Cells via Advanced Nanotexturing and Surface Recombination Suppression

Ultrafast Random‐Pyramid Texturing for Efficient Monocrystalline Silicon Solar Cells

Optimization of Rear-Side Passivation for Enhancing the Performance of Bifacial PERC+ Solar Cells

Efficient Micrometer Thick Bifacial Perovskite Solar Cells

Tailoring Interdigitated Back Contacts for High-performance Bifacial Silicon Solar Cells

Grain Regrowth and Bifacial Passivation for High‐Efficiency Wide‐Bandgap Perovskite Solar Cells

Quasi‐Omnidirectional Ultrathin Silicon Solar Cells Realized by Industrially Compatible Processes

Conductive Passivator for Efficient Monolithic Perovskite/Silicon Tandem Solar Cell on Commercially Textured Silicon