Abstract:A passivating contact structure composition of a heavily doped polysilicon (poly-Si) and a tunneling silicon oxide plays an important role in high-efficiency n-TOPCon (tunneling oxide passivated contact) solar cell, which remarkably reduces recombination losses at both the crystalline silicon rear surface and metal/Si contact interface. However, it is a great challenge for the passivating contact structure to be effectively formed on a pyramidally textured surface due to the presence of sharp vertices, edges, and valleys. In this work, the rear surface microstructure of the TOPCon solar cells was optimized by adjusting the etching time of rear surface chemical polishing after standard alkali texturization in addition to the performance on industrial TOPCon solar cells. It can be observed that the pyramidal vertices were selectively etched and the square pyramid bases were left after the rear surface polishing by using an etching solution composed of 3.4% KOH and 0.93% additive. Besides, a pyramid base with a smaller edge but a higher height could be achieved by etching a shorter time, leading to a rougher rear surface. It could help to reduce the contact resistivity without passivation degeneration, and also assisted to improve the forming ability of metal fingers in the screen-printing process. The average FF corresponding to 170 s, 230 s, and 300 s etching time conditions were 83.62%, 83.44%, and 83.45%, respectively, which is due to the difference of roughness. While a rougher rear surface resulted in a slight difference in the open circuit voltage Voc and the short circuit current Isc. Finally, 210 mm × 210 mm industrial n-TOPCon solar cells achieved an average efficiency of 24.82% at 170 s rear etching time condition, which was an absolute efficiency improvement of more than 0.05% compared with the other two longer etching times. At the same time, batch validation of more than 10,000 pieces showed similar electrical performance improvements with excellent mass producibility.

Upright Pyramids Vs. Inverted Pyramids Surface Textures: a Comparative Investigation on the Electrical Properties of PERC Solar Cells

High-Efficiency Silicon Inverted Pyramid-Based Passivated Emitter and Rear Cells

Investigations Of Random Pyramid Texture On The Surface Of Single-Crystalline Silicon For Solar Cells

Inverted Pyramid Morphology Control by Acid Modification and Application for PERC Solar Cells

Improvement of conversion efficiency of multicrystalline silicon solar cells by incorporating reactive ion etching texturing

Ultrafast Random‐Pyramid Texturing for Efficient Monocrystalline Silicon Solar Cells

Formation of Various Pyramidal Structures on Monocrystalline Silicon Surface and Their Influence on the Solar Cells

Improvement of Light Trapping in Bifacial PERC Silicon Solar Cells by Optimizing the Rear Surface Morphology

Chain pyramid texturization for better light trapping and efficiency of silicon solar cells

Effect of Rear Pyramid Structures on Industrial Bifacial PERCs under Omnidirectional Incidence

Performance Improvement of Graphene/Silicon Solar Cells via Inverted Pyramid Texturation Array

Refining the Substrate Surface Morphology for Achieving Efficient Inverted Perovskite Solar Cells

Constructing Submicron Textures on Mc-Si Solar Cells Via Copper-Catalyzed Chemical Etching

Influence of rear surface pyramid base microstructure on industrial n-TOPCon solar cell performances

High Performance Inverted RbCsFAPbI3 Perovskite Solar Cells Based on Interface Engineering and Defects Passivation.

TEXTURIZATION OF MONOCRYSTALLINE SILICON FOR SOLAR CELLS

Reflectivity of porous-pyramids structured silicon surface

Influence of the textured pyramid size on the performance of silicon heterojunction solar cell

Anti-reflection effect of high refractive index polyurethane with different light trapping structures on solar cells

Coordinated Optical Matching of a Texture Interface Made from Demixing Blended Polymers for High Performance Inverted Perovskite Solar Cells.

Effect of Surface Texture on Pinhole Formation in SiO x-Based Passivated Contacts for High-Performance Silicon Solar Cells