Abstract:Good gas permeability is an essential factor for the smooth operation and high performance in the lower part of the blast furnace. Under the present low carbon blast furnace smelting conditions, the coke layer is thinner, and the proportion of the molten metal in the coke layer is significantly higher, resulting in a major reduction in gas permeability, which seriously affects blast furnace operations. Also, the lower thickness of the coke layer weakens the process of solid-liquid carbon dissolution when the molten iron passes through the coke layer, which reduces the carbon content of the molten iron and further deepens the erosion of the refractory by the unsaturated molten iron. The carbon dissolution in the molten iron in a blast furnace core was measured by a high-temperature vacuum wettability test tool that analyzed the interface wetting activity between Fe−C melts with specific carbon mass fraction (3.8%, 4.3%, 4.8%) and 99.9% of high temperatures graphite plates. Besides, the scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS) were used to analyze the graphite substrate’s carburizing morphology and carburizing distances. The results show that, with the increase of carbon content, the interface contact angle becomes bigger. The contact angle decreases with time, and eventually reaches a steady-state during the melting process, and the Fe−C melt with saturated carbon cannot be wet. The scanning electron microscopy analysis shows that a spherical cap-like depression is created by a cross-section of the Fe−C melt and the graphite substrate, and the radius and volume of the depression decrease with increasing carbon content. The study of the EDS scanning analysis shows that the amount of dissolved carbon atoms in the graphite substrate penetrates the Fe−C melt and decreases with increasing initial carbon concentration. The smaller the carburizing effect, the better the wetting is conducive to carbon mass transfer. It is found that by measuring carburizing of the carbon atoms in the graphite substrate into the Fe−C melt by calculating the surface energy reduces the surface energy between the two. Thus, the surface tension decreases and the melt spreads slowly with contact angle gradually decreasing during melting.

Numerical Analysis of Flash Ironmaking Process in a Newly Proposed Counter-Current Downer

Numerical Analysis of the Dust Control Performance of a Counter-current Swirling Configuration in the Flash Ironmaking Reactor

Numerical Simulation of Flash Reduction of Iron Ore Particles with Biomass Syngas

Numerical Investigation of the Limit of Coke Rate Reduction in an Ironmaking Blast Furnace (BF)

Numerical Simulation of the Effect of Feeding Mode on the Reduction of Ore Powder in Hydrogen‐Based Flash Ironmaking Process

Direct reduction of iron-ore with hydrogen in fluidized beds: A coarse-grained CFD-DEM-IBM study

CFD-DEM Simulation of Flow and Mixing Behavior in Downers with Different Entrance Structures

Computational Study of Hot Gas Injection (HGI) into an Ironmaking Blast Furnace (BF)

Integrated Gas and Solid Model to Determine the Flow Performance in the SCR Reactor

A Proposal of Ore Particle-Wall Sticking Criterion During the Flash Ironmaking Process

Interface Wetting Behavior Between Iron and Coke During the Carbon Dissolution Process in a Blast Furnace

Kinetic Study of Iron Ore Fines Reduction in Circulating Fluidized Bed

Wall Reduction and Heat Transfer Characteristics of Captured Iron Ore Particles During Flash Ironmaking Process

Numerical Simulation of Multiphase Flow Behavior in Hot Metal Ladle Desulfurization with Bottom Powder Injection and Electric Field

Multiscale modeling of counter-current moving bed reactor for direct reduction of iron oxide: Unveiling influence of solid shape and pressure

A Numerical Study of the Thermochemical and Aerodynamic States of H2‐intensive Direct Reduction Shaft Furnace

Numerical Simulation of Multiphase Flow Induced by Bottom Blowing Limestone Powder in Converter Steelmaking

Numerical investigation of the impact of injecting coke oven gas on raceway evolution in an ironmaking blast furnace

Effect of different modification methods on fluidized bed hydrogen reduction of cohesive iron ore fines

Modeling Decarburization in the AOD Converter: A Practical CFD-Based Approach With Chemical Reactions

A Numerical Study on the Process of the H2 Shaft Furnace Equipped with a Center Gas Distributor