Abstract:Good gas permeability is an essential factor for the smooth operation and high performance in the lower part of the blast furnace. Under the present low carbon blast furnace smelting conditions, the coke layer is thinner, and the proportion of the molten metal in the coke layer is significantly higher, resulting in a major reduction in gas permeability, which seriously affects blast furnace operations. Also, the lower thickness of the coke layer weakens the process of solid-liquid carbon dissolution when the molten iron passes through the coke layer, which reduces the carbon content of the molten iron and further deepens the erosion of the refractory by the unsaturated molten iron. The carbon dissolution in the molten iron in a blast furnace core was measured by a high-temperature vacuum wettability test tool that analyzed the interface wetting activity between Fe−C melts with specific carbon mass fraction (3.8%, 4.3%, 4.8%) and 99.9% of high temperatures graphite plates. Besides, the scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS) were used to analyze the graphite substrate’s carburizing morphology and carburizing distances. The results show that, with the increase of carbon content, the interface contact angle becomes bigger. The contact angle decreases with time, and eventually reaches a steady-state during the melting process, and the Fe−C melt with saturated carbon cannot be wet. The scanning electron microscopy analysis shows that a spherical cap-like depression is created by a cross-section of the Fe−C melt and the graphite substrate, and the radius and volume of the depression decrease with increasing carbon content. The study of the EDS scanning analysis shows that the amount of dissolved carbon atoms in the graphite substrate penetrates the Fe−C melt and decreases with increasing initial carbon concentration. The smaller the carburizing effect, the better the wetting is conducive to carbon mass transfer. It is found that by measuring carburizing of the carbon atoms in the graphite substrate into the Fe−C melt by calculating the surface energy reduces the surface energy between the two. Thus, the surface tension decreases and the melt spreads slowly with contact angle gradually decreasing during melting.

Numerical Investigation of the Limit of Coke Rate Reduction in an Ironmaking Blast Furnace (BF)

Computational Study of Hot Gas Injection (HGI) into an Ironmaking Blast Furnace (BF)

Computational Fluid Dynamics Study of the Thermochemical Behaviors in an Ironmaking Blast Furnace with Oxygen Enrichment Operation

A Multi-Objective Optimization Model Based on Long Short-Term Memory and Non-Dominated Sorting Genetic Algorithm II

Development of simple blast furnace models for addressing carbon reduction strategies

Transient 3D CFD study of pulverised coal combustion and coke combustion in a blast furnace: Effect of blast conditions

The method of reducing energy consumption in large blast furnace smelting by increasing top pressure

Numerical Investigation of the Coupled Effect of H/D Ratio and Effective Volume on Optimized Blast Furnace Profile

Mathematical Modeling and Analyses of Integrated Process with Blast Furnace Iron Making and Co-gasification of Coal-COG-BF top gas

Computational Fluid Dynamics Study of the Flow and Thermochemical Behaviors of a Carbon Composite Briquette in an Ironmaking Blast Furnace

Numerical Investigation of Burden Distribution in Hydrogen Blast Furnace

Development of Mass–Energy Balance Model Based on a New Process of RSF with Hy-O-CR

The CO2 reduction potential for the oxygen blast furnace with CO2 capture and storage under hydrogen-enriched conditions

Study on the High-Temperature Interaction between Coke and Iron Ores with Different Layer Thicknesses

Interface Wetting Behavior Between Iron and Coke During the Carbon Dissolution Process in a Blast Furnace

A technical review on coke rate and quality in low-carbon blast furnace ironmaking

Modern blast furnace ironmaking technology: potentials to meet the demand of high hot metal production and lower energy consumption

The method of reducing energy consumption in large blast furnace smelting by low-silicon smelting

An Analysis of Long-Process Ironmaking in a Reduction Smelting Furnace with Hydrogen-Enriched Conditions

Numerical Simulation of the Effect of Feeding Mode on the Reduction of Ore Powder in Hydrogen‐Based Flash Ironmaking Process

Numerical Investigation of the Inner Profiles in Ironmaking Blast Furnace: Effect of the Ratio of Belly Diameter to Effective Height