Abstract:This paper reports the use of combined electron microscopy and small-angle neutron scattering (SANS) to probe into the compositional and size evolution of the primary carbides and nanoparticles (defined by a size threshold of 100 nm) in an additively manufactured high-alloy steel before and after heat treatment. The primary carbides exhibit marginal changes in their total volume fraction and size after the austenitising and tempering. However, those carbides located at the prior-austenite boundaries provide a pinning effect to impede grain growth during the austenitising. The grain size increases from 1.7 µm in the as-manufactured to 2.8 µm in the as-tempered conditions, resulting in a limited strength loss of 33–126 MPa as estimated by using the Hall-Petch relationship. Atom probe tomography, which offers atomic spatial resolution examining a sample volume of 6.6 × 105 nm3, reveals the presence of numerous V and Cr-enriched nanoparticles with sizes of 1 to 10 nm within the steel matrix after the tempering. In contrast, the complementary SANS which examines a significantly larger sample volume of 0.9 mm3 but lacking spatial resolution, provides nanoparticle size information. It reveals a radius reduction from 7.6 to 1.0 nm and a volume fraction increase from 1.6 % to 2.3 %, in the as-manufactured and as-tempered conditions, respectively. The nanoparticles induced during tempering can contribute to a strength enhancement of 691 MPa, primarily through the Orowan bypass mechanism. This suggests that the combination of limited prior-austenite grain growth and the presence of nanoparticles is the key factor responsible for the unprecedented material strength.

Microstructure Refinement and Strengthening–Toughening Mechanisms of Gray Cast Irons Reinforced by in Situ Nanosized TiB2–TiC/Al Master Alloy

Synergistic optimization in microstructure and mechanical properties of low carbon steel via trace amount of nano-sized TiC-TiB2

Improved Strength-Ductility of Ti-6Al-4V Casting Alloys with Trace Addition of TiC-TiB2 Nanoparticles

Versatility of trace nano-TiC–TiB2 in collaborative control of solidification-rolling-welding microstructural evolution in Al–Mg–Si alloy for enhanced properties

Simultaneously enhanced hardness and toughness of normalized graphite ductile irons by TiC-TiB2 nanoparticles

Increased tensile strength and elongation of the Ni–Fe based polycrystalline cast superalloy via the trace addition of TiC nanoparticles

Refinement Effectiveness of Self-Prepared (nbti)c Nanoparticles on As-Cast 1045 Steel

Refinement of cast microstructure of A517 steel by addition of TiB2

In-situ Observations of Grain Refinement by TiN Particles in the Simulated Coarse-Grained Heat-Affected Zone of a High-Strength Low-Alloy Steel

Role and mechanism of innovative addition process of trace nano-TiC p in microstructure manipulation and significant mechanical properties enhancement of H13 steels

Microstructure and Tensile Properties of 1-D Forged (tib+tic)/ti Composite

Microstructure and Tensile Properties of in Situ Synthesized (Tib+tic)/ti-6Al-4v Composites

Microstructure Evolution and Strengthening Mechanisms of Cast Al–Cu–Mn Alloy via Ti–Zr-Synergistic Micro-alloying

Control of a fine-grained microstructure for cast high-Cr TiAl alloys

Effect of alloying elements W, Ti, Sn on microstructure and mechanical properties of gray iron 220

An Investigation of Microstructural Evolution, Tensile Properties and Work-Hardening Behavior of Nanosized TiB2/Al-Cu-Mn Composites

Insights into primary carbides and nanoparticles in an additively manufactured high-alloy steel

Simultaneously enhanced strength and toughness of cast medium carbon steels matrix composites by trace nano-sized TiC particles

Mechanisms of Strengthening and Toughening of Austempered High Silicon Cast Steel

Preparation, Microstructure and Mechanical Properties of In-Situ TiC/Al–Si–Fe Aluminum Matrix Composites

Influence of Nanoparticles on Microstructural Evolution and Mechanical Properties of Sr-modified Al-10Si Alloys