Abstract:To reveal the refinement mechanism of Ti2AlC particle by in -situ Y2O3 in the liquid region and the improvement mechanisms of refined Ti2AlC in solid-state phase transformation process, Ti-46Al-8 Nb-2.6 C-xY alloys were prepared. Microstructures were observed by SEM, XRD and TEM, and the mechanical properties were examined. Calculated results indicated that the phase boundary energy of in -situ Y2O3 combined with TiC was low in the liquid region. TiC particle was formed initially, followed by Y2O3 particle. The Y2O3 particle moved to the surface of TiC particle to inhibit its growth, which left small -sized TiC nucleation substrate for the formation of Ti2AlC. The orientation relationship was [2200]Ti2AlC//[066]Y2O3. A stepped atomic diffusion zone was formed in the interface of Y2O3 and Ti2AlC to inhibit lateral and longitudinal growth of Ti2AlC. As Y increased from 0.02 to 0.1 at%, the average aspect ratio of Ti2AlC particles decreased from 7.7 to 3.4, the Ti2AlC content with the aspect ratio of 1-5 increased from 13.7 to 91.3%. The lamellar colony size and lamellar spacing reduced from 47.5 to 26.0 mu m and 0.74 to 0.58 mu m, respectively. Both Y2O3 and refined Ti2AlC served as heterogeneous nucleation sites and inhibited the lateral thickening rate of gamma lath. The Y -type YAl2 phase was formed as Y content exceeded 0.1 at%. The compressive strength and Vickers hardness were improved from 1801 to 2201 MPa and 443.2 to 464.5 HV, respectively. However, the subsequent decrease in strength was caused by the embrittlement of grain boundary after the precipitation of YAl2 phase. The significant refinement of Ti2AlC and lamellar colony by insitu Y2O3 and the precipitation strengthening of Ti2AlC contributed to the mechanical properties.

Microstructure Refinement Assisted by Α-Recrystallization in a Peritectic TiAl Alloy

Control of a fine-grained microstructure for cast high-Cr TiAl alloys

Microstructure refinement of a TiAl alloy by beat treatment

Microstructure refinement of cast TiAl alloys by β solidification

Metastable microstructure evolution and grain refinement in a Low-Ta containing γ-TiAl alloy through heat treatment

Grain refinement of a TiAl alloy by heat treatment through near gamma transformation

On the grain size refinement of TiAl alloys by cyclic heat treatment

Asynchronous Spheroidization of the Lamellar Structure in a Near-α Ti Alloy

A Novel Method and Mechanism for Simultaneously Refining Microstructure and Controlling Grain Orientation in Ti48Al2Cr2Nb2.5C Alloy

Deformation-Induced Grain Refinement and Amorphization in Ti-10V-2Fe-3Al Alloy

Grain refinement of 1 at.% Ta-containing cast TiAl-based alloy by cyclic air-cooling heat treatment

Microstructure refinement of Ti-40Al-8Nb alloys via the decomposition of the metastable B2 phase at 1000 °C

Investigation on Transformation-Related Recrystallization Behavior of Ti2AlNb-based Alloy

Deformation-induced Microstructure Refinement in Primary Α Phase-Containing Ti–10V–2Fe–3Al Alloy

Hierarchical Grain Refinement During the Laser Additive Manufacturing of Ti-6Al-4V Alloys by the Addition of Micron-Sized Refractory Particles

Microstructure Transformation of a Refined High Nb Containing TiAl Alloy

Enhanced Grain Refining Efficiency Assisted by Martensitic Transformation in Metastable Β-Titanium Alloy

Refining Ti2AlC in the Liquid Region and Improving the Microstructure and Mechanical Properties of Ti-46Al-8 Nb-2.6 C Alloy by Adding Y

Control of the homogeneity of the lamellar structure of a TiAl alloy refined by heat treatment

Tuning the Microstructure and Mechanical Properties of TiAl-based Alloy Through Grain Boundary Engineering

Refinement Mechanism of Centimeter-Grade Coarse Grains in As-Cast Ti2AlNb-Based Alloy Through Uniaxial and Multi-axial Compressions