Abstract:Antimony selenide (Sb2Se3) has advantages of low-toxicity, abundant and excellent photoelectric properties. It is widely considered as one of the most promising light-harvesting materials for thin-film solar cells. However, the power conversion efficiency of the Sb2Se3 thin-film solar cell is still far inferior to that of cadmium telluride, copper indium gallium selenium and perovskite solar cells. As is well known, the Sb2Se3 solar cell performance is closely related to the light absorber layer (crystallinity, composition, bulk defect density, etc.), PN heterojunction quality (charge carrier concertation, energy band alignment, interface defect density, etc.) and back-contact barrier formation, which determines the process of carrier generation, excitation, relaxation, transfer and recombination. The low fill factor is one of the core problems that limit further efficiency improvement of Sb2Se3 solar cells, which can be attributed to the high potential barrier at the back contact between the Mo electrode and Sb2Se3 absorption layer. In this work, a heat treatment is applied to the Mo electrode to generate a MoO2 buffer layer. It can be found that this buffer layer can inhibit MoSe2 film growth, exhibiting better Ohmic contact with Sb2Se3, and reducing the back contact barrier of the solar cell. The Sb2Se3 thin film is prepared by an effective combination reaction involving sputtered and selenized Sb precursor. After introducing the MoO2 buffer layer, it can also promote the formation of (hk1) (including (211), (221), (002), etc.) preferentially oriented Sb2Se3 thin films with average grain size over 1 μm. And the ratio of Sb to Se is optimized from 0.57 to 0.62, approaching to the stoichiometric ratio of Sb2Se3 thin film and inhibiting the formation of Vse and SbSe defects. Finally, it enhances the open-circuit voltage (VOC) of solar cells from 0.473 to 0.502 V, the short-circuit current density (JSC) from 22.71 to 24.98 mA/cm2, and the fill factor (FF) from 46.90% to 56.18%, thereby increasing the power conversion efficiency (PCE) from 5.04% to 7.05%. This work proposes a facile strategy for interfacial treatment and elucidates the related carrier transport enhancement mechanism, thus paving a bright avenue to breaking through the efficiency bottleneck of Sb2Se3 thin film solar cells.

Enhanced Performance of the Sb2Se3 Thin-Film Solar Cell by Organic Molecule-Induced Crystallization and Suppression of the Interface Recombination

Enhanced Performance of the Sb 2 Se 3 Thin-Film Solar Cell by Organic Molecule-Induced Crystallization and Suppression of the Interface Recombination

Heterogeneous Nucleation Regulation Amends Unfavorable Crystallization Orientation and Defect Features of Antimony Selenosulfide Film for High‐Efficient Planar Solar Cells

Enhanced efficiency of the Sb2Se3 thin-film solar cell by the anode passivation using an organic small molecular of TCTA

Interfacial Engineering Towards Enhanced Photovoltaic Performance of Sb2Se3 Solar Cell

Thermal Diffused Post-Selenization for Enhancing the Photovoltaic Performance of Thermally Evaporated Sb2Se3 Solar Cell

Enhanced Photovoltaic Properties in Sb2S3 Planar Heterojunction Solar Cell with a Fast Selenylation Approach

Optimizing Crystal Orientation and Defect Mitigation in Antimony Selenide Thin-Film Solar Cells through Buffer Layer Energy Band Adjustment

Chemical Etching Induced Surface Modification and Gentle Gradient Bandgap for Highly Efficient Sb2(S,Se)3 Solar Cell

Carrier Transport Enhancement Mechanism in Highly Efficient Antimony Selenide Thin‐Film Solar Cell

Thermal diffused post-selenization for enhancing the photovoltaic performance of thermally evaporated Sb 2 Se 3 solar cell

Efficient CdS/Sb2S3 Interfacial Modification Using Sodium Borohydride Etching for Enhanced Performance of Low-Cost Full-Inorganic Antimony-Based Solar Cells

Interface Optimization and Defects Suppression Via NaF Introduction Enable Efficient Flexible Sb2Se3 Thin-Film Solar Cells

Efficient CdS/Sb 2 S 3 interfacial modification using sodium borohydride etching for enhanced performance of low-cost full-inorganic antimony-based solar cells

Solvent Annealing Enabling Reconstruction of Cadmium Sulfide Film for Improved Heterojunction Quality and Photovoltaic Performance of Antimony Selenosulfide Solar Cells

Back Contact Optimization for Sb<sub>2</sub>Se<sub>3</sub> Solar Cells

Solution-processed SnO2 interfacial layer for highly efficient Sb2Se3 thin film solar cells

Solution‐Processed Sb2(S, Se)3 Seeds‐Assisted Sb2Se3 Thin Film Growth for High Efficiency Solar Cell

Hydrazine Hydrate‐Induced Surface Modification of CdS Electron Transport Layer Enables 10.30%‐efficient Sb2(S,Se)3 Planar Solar Cells

Fabricating High‐Efficiency Sb2(S,Se)3 Solar Cells by Novel Additive‐Assisted Longitudinal Component Engineering

Interface optimization and defects suppression via NaF introduction enable efficient flexible Sb 2 Se 3 thin-film solar cells