Abstract:The changes in loading rate and test temperature influence deformation (yield and flow) and fracture behavior of steel. The most significant effect of increasing loading rate is to shift the quasi-static fracture toughness transition curve toward higher temperatures, that is, to raise the temperatures at which cleavage may occur. This is very critical for structural steel components. The high strain rate sensitivity of these steels makes the safety design on the basis of quasi-static behavior rather poor. Therefore, the reliability of structures possibly loaded at higher loading rates requires the knowledge of the corresponding material fracture behavior. However, the effects of loading rate on the cleavage fracture mechanism, fracture stress and toughness of various steels have not been understood completely. Specifically, the prediction of the cleavage fracture behavior in notched specimens and actual structures and components loaded at various loading rates remain to be learned. In engineering structures and components possibly loaded at various loading rates, notch defects may be difficult to avoid and some notch-like geometries are necessary for structure design. Therefore, the understanding of notch toughness at various loading rates is also very important. In this work, the effects of loading rate, notch geometry and loading mode on the cleavage fracture behavior of 16MnR steel were studied by experiments and FEM calculations. The results show that the cleavage fracture mechanism of this steel, the corresponding local cleavage fracture stress sigma(f) and macroscopic cleavage fracture stress sigma(F) do not change with the above three factors. The change of the notch toughness of the notched specimens with different notch geometries and loading modes with loading rates can be predicated by the criterion sigma(yymax) >= sigma(F), where sigma(yymax) is the maximum normal stress ahead of a notch and can be obtained by FEM calculations. The sigma(F) can be regarded as an engineering notch toughness parameter, and may be used for assessing the integrity of structures with notch defects. The sigma(F) values of steels can be measured by the Griffiths-Owen notched specimen at prescribed test temperature and loading rate.

Creep Damage and Interaction Behavior of Neighboring Notches in Components at Elevated Temperature

Notch Effect on Structural Strength of Components at Elevated Temperature under Creep, Fatigue, and Creep-Fatigue Loading Conditions: Phenomenon and Mechanism

Creep Damage in 9-12% Cr Steel Notched Components: Microstructural Evolution and Stress State Dependence

Notch Behavior of Components under the Stress-Controlled Creep-Fatigue Condition: Weakening or Strengthening?

Assessment on Strain-Based and Stress-Based Design Strategies for Components at Elevated Temperatures: A Comparative Study

Notch Effect on Creep Damage for Hastelloy C276-BNi2 Brazing Joint

Stress State Dependent Creep Damage Behavior of 9–12% Cr Steel Notched Components

Effect of Notch Position on Creep Damage for Brazed Joint

Effects of Creep Ductility and Notch Constraint on Creep Fracture Behavior in Notched Bar Specimens

Numerical simulation of creep notched bar of P91 steel

Creep Failure Behavior of Notched Structure in the Simulated Steam Turbine Rotor: Experimental and Damage Analysis

Effects of residual stress on creep damage and crack initiation in notched CT specimens of a Cr-Mo-V steel

On the plastic strain accumulation in notched bars during high temperature creep dwell

EFFECTS OF LOADING RATE,NOTCH GEOMETRY AND LOADING MODE ON THE CLE AVA GE FRACTURE BEHAVIOR OF 16mnr STEEL

A Time-Dependent Stress and Strain Estimation Method for Notched Components under Displacement-Controlled Condition

Advances on Creep–fatigue Damage Assessment in Notched Components

Probabilistic notch fatigue assessment under size effect using micromechanics-based critical distance theory

Effect of elliptical notches on mechanical response and progressive damage of FMLs under tensile loading

Fatigue life prediction of notched components under size effect based on strain energy density gradient

A Time‐dependent Stress and Strain Estimation Method for Notched Components of Power‐law Creep Materials under Combined Primary and Secondary Loads

Modeling of fatigue crack growth from a notch