Abstract:A statistical analysis of plastic deformation mechanisms was performed on an extruded Mg-3 wt%Y sheet during room temperature uniaxial compression along the extrusion direction. Grain-scale slip trace analysis and twin variant analysis were performed grain-by-grain to reveal the active slip/twinning systems based on quasi-in-situ SEM and EBSD. The initial microstructure was fully recrystallized exhibiting typical rare-earth texture characteristics. The true stress-true plastic strain curve showed a sigmoidal shape indicating a profuse twinning activity which was consistent with the twin analysis. After 10% strain, there were 78 out of ~700 grains exhibited slip trace. In addition to the dominated basal slip (79.5%), considerable non-basal slips including 2nd pyramidal slip (11.5%) following prismatic slip (9%) were active. For twinning activity, among the ~250 grains analyzed at 10% strain, all the identified ~150 twins were tension twins with an area fraction of 19%. The twin variant selection did not solely follow the Schmid law, i.e. 42.3% twins exhibited low Schmid factor values (m<0.2) and 5.4% m values was negative. However, the proposed normalized m (mnor) can correlate the variant selection more effectively, and over 80% twins exhibited large mnor values. Twin transmission at grain boundary was observed for over 50% twins, and only 43.6% of them had high Luster-Morris parameter values (m’>0.75). However, the transmitted pairs with both large mnor sum and normalized m’ were preferred, and the fraction was over 64%. The twined number fraction was closely related to the maximum m values of prismatic slip. The present work implied that the twinning behavior is greatly dependent on the local conditions, and slip and twinning are closely related.

Tension-compression Asymmetry and the Underlying Slip/twinning Activity in Extruded Mg–Y Sheets

Effects of Y on the Deformation Mechanisms of Extruded Mg-Y Sheets During Room-Temperature Compression

Role of Yttrium Content in Twinning Behavior of Extruded Mg-Y Sheets under Tension/compression

A Statistical Analysis of Compressive Deformation Mechanisms in an Extruded Mg–3Y Sheet

Quantitative Study on Slip/twinning Activity and Theoretical Critical Shear Strength of Mg Alloy with Y Addition

Anomalous Temperature-Dependent Strength and the Underlying Slip Activity in an Extruded Mg-10Y (wt.%) Sheet

Tension-compression Asymmetry of Extruded Mg-Gd-Y-Zr Alloy with a Bimodal Microstructure Studied by In-Situ Synchrotron Diffraction

Observation of Non-Basal Slip in Mg-Y by in Situ Three-Dimensional X-ray Diffraction

Quantitative Investigation on the Slip/Twinning Activity and Cracking Behavior During Low-Cycle Fatigue of an Extruded Mg-3Y Sheet

Study of Slip Activity in a Mg-Y Alloy by in Situ High Energy X-ray Diffraction Microscopy and Elastic Viscoplastic Self-Consistent Modeling

Deformation mechanisms of basal slip, twinning and non-basal slips in Mg–Y alloy by micropillar compression

Identification and Analysis of Anomalous {101‾2} Twins in an Extruded Mg-2wt%Y Alloy Sheet During Uniaxial Tensile Loading

The Discrepancy in Basal Slip Hardening Rates of Cast and Extruded Mg-Y-Zr Alloys

Critical resolved shear stresses for slip and twinning in Mg-Y-Ca alloys and their effect on the ductility

Texture Evolution and Deformation Activity of an Extruded Magnesium Alloy: Effect of Yttrium and Deformation Temperature

Tension-compression Asymmetry of a Rolled Mg-Y-Nd Alloy

Tension–Compression Yield Asymmetry Influenced by the Variable Deformation Modes in Gradient Structure Mg Alloys

The Improved Tension-Compression Asymmetry with Double-Extrusion for Mg-Sn-(Y) Alloys

Study of Basal < a > and Pyramidal < C + a > Slips in Mg-Y Alloys Using Micro-Pillar Compression

Improving Tension/Compression Asymmetry of a Hot‐Extruded Mg–Zn–Y–Zr Alloy Via Yttrium Addition

Anisotropic cyclic deformation behavior of an extruded Mg-3Y alloy sheet with rare earth texture