Abstract:The differences in the deformation mechanisms during uniaxial tension of cast and extruded Mg–2Y-0.5Zr (wt%) alloys have been investigated by using EBSD-based slip trace analysis and VPSC simulation methods, and a novel method for counting the activity of slip/twinning using grain area has been proposed. Slip trace analysis reveals that enhanced ductility and reduced tensile-compressive asymmetry observed in the Mg–2Y-0.5Zr (wt%) alloy can be attributed to the addition of the Y element, which modified the texture, and promoted pyramidal slip and suppressed prismatic slip. The extruded alloy exhibits a distinctive pseudo-fiber bimodal microstructure, which contributes to its superior ductility. The VPSC results indicate that the CRSSnon-basal/CRSSbasal ratio of the extruded alloys decreases, whereas the CRSStwinning/CRSSbasal ratio increases, which is attributed to the different effects of the grain refinement on the different deformation modes. In addition, both the VPSC results and the slip trace analysis results indicate that the extruded alloy exhibits reduced non-basal slip activity compared to the cast alloy at similar strain levels. The work-hardening rate curves and VPSC parameters give a reasonable explanation that the key to the increase in the ductility of Mg–Y–Zr alloys after extrusion is the decrease in the basal hardening rate rather than the non-basal slip activity. The refinement of grain size leads to a significant decrease in basal slip hardening rate, primarily due to the decrease in the additional hardening effect caused by tensile twinning and the generation of an additional GBS mechanism in the pseudo fiber microstructure.

Study of Basal < a > and Pyramidal < C + a > Slips in Mg-Y Alloys Using Micro-Pillar Compression

Deformation mechanisms of basal slip, twinning and non-basal slips in Mg–Y alloy by micropillar compression

Critical resolved shear stresses for slip and twinning in Mg-Y-Ca alloys and their effect on the ductility

Effects of Y on the Deformation Mechanisms of Extruded Mg-Y Sheets During Room-Temperature Compression

Observation of Non-Basal Slip in Mg-Y by in Situ Three-Dimensional X-ray Diffraction

Tension-compression Asymmetry and the Underlying Slip/twinning Activity in Extruded Mg–Y Sheets

Deformation mechanisms of Mg-Ca-Zn alloys studied by means of micropillar compression tests

The Discrepancy in Basal Slip Hardening Rates of Cast and Extruded Mg-Y-Zr Alloys

Study of Slip Activity in a Mg-Y Alloy by in Situ High Energy X-ray Diffraction Microscopy and Elastic Viscoplastic Self-Consistent Modeling

Quantitative Study on Slip/twinning Activity and Theoretical Critical Shear Strength of Mg Alloy with Y Addition

Grain-scale deformation in a Mg−0.8 wt% Y alloy using crystal plasticity finite element method

In-situ Analysis of the Slip Activity During Tensile Deformation of Cast and Extruded Mg-10Gd-3Y-0.5Zr (wt.%) at 250°C

Origins and dissociation of pyramidal <c + a> dislocations in magnesium and its alloys

Characterisation of the strain rate sensitivity of basal, prismatic and pyramidal slip in Zircaloy-4 using micropillar compression

In-situ Analysis of Slip Transfer and Heterogeneous Deformation in Tension of Mg-5.4Gd-1.8Y-1.5Zn Alloy

Experimentally Quantifying Critical Stresses Associated with Basal Slip and Twinning in Magnesium Using Micropillars

Ex-situ EBSD investigation of the reduced c/a values and work hardening behavior in Mg-4Li-1Al-0.5Y alloy under hot compression

Precipitate strengthening of pyramidal slip in Mg-Zn alloys

Anomalous Temperature-Dependent Strength and the Underlying Slip Activity in an Extruded Mg-10Y (wt.%) Sheet

Dislocation behavior in a polycrystalline Mg-Y alloy using multi-scale characterization and VPSC simulation

Deformation mechanisms, activated slip systems and critical resolved shear stresses in an Mg-LPSO alloy studied by micro-pillar compression