Abstract:Mg–Y alloys show distinctly different slip/twinning activity under quasi-static monotonic loading at room temperature compared with pure Mg, as extensively reported. In this work, the influences of 3% Y addition on the deformation modes and transferability during strain-controlled tension-compression low-cycle fatigue (LCF) at room temperature of Mg sheets were studied quantitatively and statistically. The activity of various slip systems and twinning-detwinning were measured at desired fatigue stages via quasi-in-situ EBSD observations together with slip trace analysis. The results indicate that the activation of deformation modes in pure Mg was featured by the cyclic transition, i.e., tension twinning (at the compressive reversal) → detwinning + basal slip (at the tensile reversal). In Mg–3Y alloy, basal slip dominated the cyclic deformation throughout the fatigue life span. Compared with pure Mg, Mg–3Y alloy displayed the enhanced activity of various slip systems, including basal, prismatic, and pyramidal slip systems, but lower twinning-detwinning activity. For deformation transferability, mk, which is the product of the Schmid factor (SF) and the geometric compatibility factor (m’) values of the adjacent grains, was used to evaluate the slip transferability and twinning transferability at grain boundaries. Mg–3Y alloy showed a higher likelihood of slip transfer but lower twinning transferability than pure Mg. The underlying mechanisms affecting the activity of various slip systems and twinning, as well as deformation transferability and mechanical behavior, were discussed.

Grain-scale deformation in a Mg−0.8 wt% Y alloy using crystal plasticity finite element method

Deformation mechanisms of basal slip, twinning and non-basal slips in Mg–Y alloy by micropillar compression

Orientation dependence of intracrystalline and grain boundary deformation behavior in Mg-2Y using nanoindentation and CPFEM

Simulation on Microstructure Evolution and Mechanical Properties of Mg−Y Alloys: Effect of Trace Y

Enhancing the strain hardening and ductility of Mg-Y alloy by introducing stacking faults

Critical resolved shear stresses for slip and twinning in Mg-Y-Ca alloys and their effect on the ductility

Double-peak Strain Hardening Behavior of Mg–1.2 wt.%Y Alloy

Deformation mechanism of fine grained Mg–7Gd–5Y–1.2Nd–0.5Zr alloy under high temperature and high strain rates

The deformation modes and transferability during low-cycle fatigue of Mg and Mg–3Y alloy

Role of micro-alloying element in dynamic deformation of Mg-Y alloys

Dynamic mechanical response and deformation-induced co-axial nanocrystalline grains facilitating crack formation in magnesium-yttrium alloy

Effect of yttrium addition on dynamic mechanical properties, microstructure, and fracture behavior of extrusion-shear ZC61 + xY (x = 0, 1, 2, 3) alloys

The high-temperature deformation and microstructural evolution mechanism of Mg-Gd-Y-Zn-Zr alloy formed by CMT arc additive forming

Crystal plasticity based modeling of grain boundary sliding in magnesium alloy AZ31B sheet

The abnormal flow behavior of Mg-9Gd-4Y-2Zn-0.5Zr alloy during hot tensile deformation at high temperature and low strain rate

Grain-size effect on the deformation of Mg–3Al–3Sn alloy: Experiments and elastic-viscoplastic self-consistent modeling

Role of Y on the microstructure and mechanical properties of Mg-Gd-Zr alloy

Operating slip modes and inhomogeneous plastic deformation of Mg-10Gd-3Y-0.5Zr alloy during compression

Microstructures, hot tensile deformation behavior and constitutive modeling in a superlight Mg-2.76Li-3Al-2.6Zn-0.39Y alloy

Controlling the Plastic Anisotropy of Magnesium Alloy by Tailoring the Grain Size and Yttrium Content

Effect of rare earth element on amorphization and deformation behavior of crystalline/amorphous dual-phase Mg alloys