Abstract:Hard and brittle Fe-rich phases are formed during the solidification of recycled Al–Cu alloys, significantly decrease the mechanical properties of the alloy. In this study, optical microscopy (OM), scanning electron microscopy (SEM), electron backscattering diffraction (EBSD), X-ray diffraction (XRD), synchrotron X-ray imaging and thermodynamic calculations were used to investigate the microstructure evolution influenced by ultrasonic melt processing (USMP) and cooling rate during solidification. The results show that increasing the cooling rate after USMP significantly refines the α-Al grain size and inhibited the growth of Fe-rich phase, Al 2 Cu and pores. The three-dimensional (3D) morphologies of the Fe-rich phase and Al 2 Cu changed from coarse dispersion to fine compact, their local thickness and mean radius decrease. The observed effects are attributed to the fact that both USMP and increased cooling rate reduce α-Al grain size, leading to the growth of the eutectic Fe-rich phase and Al 2 Cu within the confined spaces between the α-Al dendrites during the late solidification stage. The cooling rate of 1.2Fe alloy increases from 0.1 °C/s to 1.5 °C/s, there is a rise in the number of Fe-rich phases, accompanied by a decrease in their dimensions. Meanwhile, the increased cooling rate inhibits the diffusion of Fe elements, which in turn promotes the growth of the Fe-rich phase. Also, an increased increasing the cooling rate after USMP can inhibit the growth of pores, especially in 0.7FeU alloy, where the pores basically disappear.

Mechanical properties of Fe-Al-Ta eutectic composites at higher solidification rates

High Temperature Tensile Property and Fracture Behavior of Directionally Solidified Fe-Al-Ta Eutectic Composites

Microstructure and fracture toughness of the Bridgman directionally solidified Fe-Al-Ta eutectic at different solidification rates

Crystal growth mechanism of directionally solidified Fe–Al–Ta eutectic composites at higher solidification rates

Tensile and fatigue properties of the Bridgman directionally solidified Fe-Al-Ta eutectic

Compressive Property and Toughening Mechanism of Directionally Solidified Fe(Al, Ta)/Fe2Ta (Al) Eutectic Composites

Achieving Enhanced Strength Retention at Elevated Temperatures in Ultrafine-Fibrous Interconnected Al-Ce-Ni Eutectic Alloy Solidified under Super-Gravity Field

In-situ observations of solidification process of Fe–Al–Ta eutectic alloy

Investigation on the solidification microstructure, microsegregation and mechanical properties of CF/Al-4.5Cu metal matrix composites

Effect of Cooling Rate on Solidification Parameters and Microstructure of Al-7Si-0.3Mg-0.15Fe Alloy

Microstructure and solidification behaviour of Ni3Al/Ni7Hf2 eutectic alloy

Effect of Solidification Sequence on the Microstructure and Mechanical Properties of Die-Cast Al–11Si–2Cu–Fe Alloy

Microstructure evolution, Cu segregation and tensile properties of CoCrFeNiCu high entropy alloy during directional solidification

Effects of Aluminum on Microstructure and Compressive Properties of Al-Cr-Fe-Ni Eutectic Multi-Component Alloys

Transition of Solid-Liquid Interface and Tensile Properties of CoCrFeNi High-Entropy Alloys During Directional Solidification

Effects of Heating Power on Microstructure Evolution and Tensile Properties at Elevated Temperature by Directional Solidification for Ti2AlC/TiAl Composites

Effect of ultrasonic melt processing and cooling rate on microstructure evolution of Al–Cu–Mn–Mg–Fe–Si alloy

Effect of Growth Rate on the Tensile Properties of DS NiAl/Cr(Mo) Eutectic Alloy Produced by Liquid Metal Cooling Technique

Microstructure evolution, phase decomposition and transition of Al0.8Co0.5Cr1.5CuFeNi HEA during high temperature sintering and mechanical properties corresponding to different microstructures

Microstructural evolution and mechanical property of Al–Mg–Mn alloys with various solidification cooling rates

Strength improvement and fracture mechanism in Fe40Al/TiC composites with high content of TiC