Abstract:Co-Cr-Fe-Ni-Ta eutectic multi-principal element alloys (MPEAs) demonstrate great potential to replace structural alloys in engineering applications. However, the cost of these alloys is high due to the usage of a number of precious metals. To decrease the cost, the present work developed a set of novel Fe 55 Cr 15 Ni 30− x Ta x ( x = 0, 5, 8, 10 and 15 at.%) eutectic MPEAs and the effect of Ta on microstructure and compressive mechanical properties were investigated for the first time. As the Ta content increases, the microstructure change from a single-phase FCC solid solution ( x = 0) to hypoeutectic microstructure ( x = 6), then to eutectic microstructure ( x = 8), and eventually to hypereutectic microstructure ( x = 10 and 15). The yield strength and the hardness increase at the expense of ductility reduction with increasing Ta content. The strengthening mechanism of this alloy system is mainly second-phase strengthening caused by Laves phase and grain boundary strengthening produced by eutectic interface, supplemented by solid solution strengthening. The Fe 55 Cr 15 Ni 22 Ta 8 and Fe 55 Cr 15 Ni 20 Ta 10 alloy present the excellent comprehensive mechanical properties. The yield strength, fracture strength and fracture strain of the former are 838 MPa, 1994 MPa and 45.1%, respectively. The yield strength, fracture strength and fracture strain of the latter are 1029 MPa, 1956 MPa and 43.0%, respectively. The phase formation of Fe 55 Cr 15 Ni 30− x Ta x alloys can be predicted by Md criterion. When Md ≥ 0.89, the alloys consist of FCC phase and Laves phase. Otherwise, the alloys consist of FCC single phase.

Microstructure and fracture toughness of the Bridgman directionally solidified Fe-Al-Ta eutectic at different solidification rates

Tensile and fatigue properties of the Bridgman directionally solidified Fe-Al-Ta eutectic

Compressive Property and Toughening Mechanism of Directionally Solidified Fe(Al, Ta)/Fe2Ta (Al) Eutectic Composites

High Temperature Tensile Property and Fracture Behavior of Directionally Solidified Fe-Al-Ta Eutectic Composites

Mechanical properties of Fe-Al-Ta eutectic composites at higher solidification rates

Crystal growth mechanism of directionally solidified Fe–Al–Ta eutectic composites at higher solidification rates

In-situ observations of solidification process of Fe–Al–Ta eutectic alloy

The microstructure and mechanical properties of novel Fe-rich Fe-Cr-Ni-Ta eutectic multi-principal element alloys

Achieving Enhanced Strength Retention at Elevated Temperatures in Ultrafine-Fibrous Interconnected Al-Ce-Ni Eutectic Alloy Solidified under Super-Gravity Field

High Temperature Oxidation Behavior of Directionally Solidified Fe(Al,Ta)/Fe2Ta(Al) Eutectic Composite

High-temperature microstructure stability and fracture toughness of TiAl alloy prepared via electron beam smelting and selective electron beam melting

Microstructure of Directionally Solidified Al2O3/EAG Eutectic Ceramics Prepared with High-Temperature Gradient

Microstructure and bending behavior of Ti/Al laminated composites reinforced with high-entropy alloy particles

Tensile properties and fracture toughness of TiAl alloys with controlled microstructures

Strength improvement and fracture mechanism in Fe40Al/TiC composites with high content of TiC

Microstructure evolution during directional solidification of off-eutectic Al-Cu-Mg alloys

The formation mechanism of eutectic microstructures in NiAl-Cr composites

Microstructural evolution, bonding mechanism and mechanical properties of AlCoCrFeNi2.1 eutectic high entropy alloy joint fabricated via diffusion bonding

Solidification and microstructure investigation on as-cast and annealed hypoeutectic Ti–Fe alloys

Anisotropic microstructures and mechanical properties of textured Ti3AlC2/TiAl3/Al composite

Microstructural morphology effects on fracture toughness and crack growth behaviors in a high strength titanium alloy