Abstract:One of the most critical aspects in understanding the deformation behavior of two-phase titanium alloys subjected to thermomechanical processes (TMPs) lies in being able to describe the flow stress accurately. To this end, in this study, initially, hot tension tests were conducted on a two-phase Ti-6Al-2Zr-1Mo-1V alloy. It was observed that the flow stress at a given temperature and strain rate exhibits work hardening, followed by flow softening. Flow softening occurs at the peak strain, where the maximum stress is observed; peak strain decreases with increasing temperature and decreasing strain rate. Variations in peak strain are more obvious at low temperatures and high strain rates. Later, the microstructure of the alloy was analyzed and the results show that work hardening and flow softening are caused by dynamic recrystallization (DRX). The DRX volume fraction was found to exhibit an increasing trend and discontinuous dynamic recrystallization (DDRX) was observed at increasing temperature and decreasing strain rate. With respect to microstructure evolution, a unified model consisting of a thermally activated stress component and an athermal stress component was developed. In the athermal stress term, dislocation density and the Hall-Petch effect were used to describe the work-hardening and flow-softening behavior. In the case of the dislocation term, the DRX effects were modeled considering the critical strain for DRX initiation and the DRX rate, which are both temperature-and strain rate-dependent. In the Hall-Petch effect term, the dependence of the Hall-Petch coefficient on the processing conditions was considered and the loss of Hall-Petch strengthening with deformation was modeled. Using the proposed model, the work-hardening and flow-softening behavior and microstructure evolution in Ti-6Al-2Zr-1Mo-1V alloys subjected to TMP were predicted. A good agreement could be observed between the experimental and predicted results. This study provides a solution for modeling work-hardening and flow-softening behavior and helps us understand the deformation behavior of two-phase titanium alloys subjected to TMP.

Microstructure Sensitive Flow Stress Based on Self Consistent Method

A New Microstructure-Sensitive Flow Stress Model for the High-Speed Machining of Titanium Alloy Ti–6Al–4V

Constitutive Model of Aviation Aluminum-Alloy Material in Metal Machining

Unified Modeling of Work Hardening and Flow Softening in Two-Phase Titanium Alloys Considering Microstructure Evolution in Thermomechanical Processes

The Role of Material Model in the Finite Element Simulation of High-Speed Machining of Ti6Al4V

Chip Fracture Behavior in the High Speed Machining of Titanium Alloys

Finite element simulation of residual stress in machining of Ti-6Al-4V with a microstructural consideration

Simulation of Material Side Flow Using a 3D Coupled Eulerian-Lagrangian Approach and a Constitutive Model Considering the Stress State

Machining Simulation of Ti6Al4V Using Coupled Eulerian-Lagrangian Approach and a Constitutive Model Considering the State of Stress

Microhardness Prediction Based on a Microstructure-Sensitive Flow Stress Model During High Speed Machining Ti-6Al-4V

A Modified Constitutive Model Coupled with Microstructure Evolution Incremental Model for Machining of Titanium Alloy Ti–6Al–4V

Extrapolation Based Constitutive Modeling of Flow Stress of Titanium Alloy Sheet under Hot-Working Condition

Micromechanical Behaviour of TA15 Alloy Cylindrical Parts Processed by Multi-Pass Flow Forming

Determination of Flow Stress Based on Cutting Simulation and Optimization

Simulation of Mechanical Response in Machining of Ti-6Al-4V Based on Finite Element Model and Visco-Plastic Self-Consistent Model

Role of Tool Flank Wear and Machining Speed in Developing of Residual Stress in Machined Surface During High Speed Machining of Titanium Alloys

Dynamic Response of Conventional and Hot Isostatically Pressed Ti–6Al–4V Alloys: Experiments and Modeling

A Hybrid Cutting Force Model for High-speed Milling of Titanium Alloys

Microstructure alteration in the high-speed machining of titanium alloy involved with tool wear and cryogenic condition

A constitutive model on flow stress prediction from the contribution of twin and grain refinement, strain and strain rate during surface mechanical attrition treatment of metals

MPM Simulations of High-Speed Machining of Ti6Al4V Titanium Alloy Considering Dynamic Recrystallization Phenomenon and Thermal Conductivity