Abstract:The microsfructure alteration generated in the high-speed machining of titanium alloy has significant influence on the performance, quality and service life of production. The prediction of grain size or phase distribution based on physics mechanism or the regression of experimental data have been reported in the process of static or quasi-static state. However, it is still a challenge to predict the phase fransformation and grain growth process in machining accurately and effectively since it has characteristics of high strain, strain rate and temperature. In this paper, a novel FEM-based model involving with the microstructure alteration was introduced and implemented to predict finial grain size or phase result in the high-speed machining of Ti-6Al-4V alloys especially at the machined surface. The phase fransformation process was proposed and discussed by considering tool wear and cryogenic condition at machined surface, while the microsfructure results were displayed on the chip in the previous works. Firstly, the phase volume fraction and grain size were modelled by experimental data. Then the simulation based on the self-consistent method (SCM) was used to output strain and temperature distribution. Thirdly, the phase volume fraction and grain size expressions were transmitted into subroutine programs and the microstructure alteration process under the different cutting conditions were showed in the FE results. The simulation results of temperature, phase fraction and strain were compared against previous simulation or experiment results in published papers revealing good agreement. The proposed model was further to investigate the influence of tool wear and cutting temperature on machined surface. The results indicated that the tool wear increased heat at the flank face significantly resulting to beta phase increasing and grain growth at machined surface and the cryogenic condition would lower temperature gradient as well as stress gradient contributing to reduce roughness and residual stress.

Microstructure alteration in the high-speed machining of titanium alloy involved with tool wear and cryogenic condition

Metallurgical-Based Prediction of Stress-Temperature Induced Rapid Heating and Cooling Phase Transformations for High Speed Machining Ti-6al-4v Alloy

Multiscale Simulation of Grain Refinement Induced by Dynamic Recrystallization of Ti6Al4V Alloy During High Speed Machining

Thermo-metallo-mechanical based phase transformation modeling for high-speed milling of Ti–6Al–4V through stress-strain and temperature effects

Quantification Of Microstructural Features And Prediction Of Mechanical Properties Of A Dual-Phase Ti-6al-4v Alloy

Improved Dynamic Recrystallization Modeling in the High-Speed Machining of Titanium Alloy

Chip Fracture Behavior in the High Speed Machining of Titanium Alloys

Correction of the constitutive model and analysis of chip formation in cryogenic machining of TA15 titanium alloy

Microhardness Prediction Based on a Microstructure-Sensitive Flow Stress Model During High Speed Machining Ti-6Al-4V

Microstructure Evolution of Ti-6Al-4V Alloy During High Speed Cutting: an Investigation Using Finite Element Simulation

FEM-simulation of Machining Induced Surface Plastic Deformation and Microstructural Texture Evolution of Ti-6Al-4V Alloy

Evolutions of grain size and micro-hardness during chip formation and machined surface generation for Ti-6Al-4V in high-speed machining

A New Microstructure-Sensitive Flow Stress Model for the High-Speed Machining of Titanium Alloy Ti–6Al–4V

Experimental study on fracture mechanism transformation in chip segmentation of Ti-6Al-4V alloys during high-speed machining

Microstructure evolution modeling of Ti6Al4V alloy during cutting using the Particle Finite Element Method and homogeneous field distributions

Finite element simulation of residual stress in machining of Ti-6Al-4V with a microstructural consideration

Tool wear-induced microstructure evolution in localized deformation layer of machined Ti–6Al–4V

Finite Element Analysis on the Chip Formation Mechanism of Titanium Alloy's High Speed Machining

Machined Surface Analysis in High-Speed Dry Milling of Ti-6al-4v Alloy with Coated Carbide Inserts

Finite Element and Experimental Analysis of Grain Refinement Caused by Dynamic Recrystallization During High-Speed Cutting of Nickel-Based Superalloys

Investigation of the Grain Refinement Mechanism in Machining Ti-6Al-4V: Experiments and Simulations