Abstract:This paper presents a high-resolution analog front-end (AFE) circuit operating in the 25 kHz signal bandwidth. The AFE consists of a capacitively-coupled chopper instrumentation amplifier (CCIA) and a third-order delta-sigma modulator (DSM). Signal distortion often occurs at the junction of CCIA and DSM, so the resistor-based discrete-time DSM (RB DT–DSM) is proposed to solve this problem. Both conventional DT–DSM and the proposed RB DT–DSM are designed and compared through simulations and chip measurements. When a conventional DT–DSM is used, a switched-capacitor integrator with a large capacitor and switch are connected to the CCIA output node, so large switching noise, significant charge injection, and a long settling time occur at the CCIA output, resulting in harmonic distortions. Therefore, CCIA requires more power consumption to reduce the settling time for conventional DT–DSM architectures. On the other hand, when the proposed RB DT–DSM is used, only a resistor and a small switch are connected to the CCIA output. Due to this novel interface technique, the switching noise is very small at the CCIA output, and the settling of the CCIA becomes fast. As a result, it is possible to effectively eliminate harmonic distortions while reducing the power requirement of the CCIA. Both the conventional and proposed AFE circuits were manufactured by a 0.18- $mu text{m}$ complementary metal-oxide-semiconductor (CMOS) process. The conventional AFE shows a peak SNR of 101.1 dB and a peak SNDR of 91.2 dB. The proposed AFE with RB DT–DSM shows a peak SNR of 101.3 dB and a peak SNDR of 100.5 dB, which verifies the significant reduction in harmonic distortions.

A 130-Db CMRR Instrumentation Amplifier with Common-Mode Replication

A novel current-mode instrumentation amplifier with Rail-to-Rail input and output

The Design of a Low-Voltage Rail-to-Rail CMOS Operational Amplifier

High-Speed Operational Amplifier Based on 0.5 Μm CMOS Process

An Analysis and Implementation of Common Mode Feedback in High-Speed Fully Differential Op-Amp

A Front-End Circuit With 16-Channel 12-Bit 100-Ksps Rc-Hybrid Sar Adc For Industrial Monitoring Application

A 2.1/5.2-NEF/PEF Capacitively Coupled Instrumentation Amplifier with Fast - Settling for Biosensor

A 7.5Gω-Input-impedance 109Db-Total-cmrr and 80Vpp-Cmi-tolerance Instrumentation Amplifier for Dry-Contact Two-Electrode ECG Monitoring

A PVT-Robust and 73.9 mHz High-Pass Corner Instrumentation Amplifier with an SCF-SCR-PR Hybrid Feedback Resistor

A 3.6 Μw 60 Nv/sqrthz Capacitively-Coupled Instrumentation Amplifier for Biopotential Signal Recordings.

Design of Common-Mode Feedback for High-Gain Charge Amplifier

A low-noise CMOS front-end amplifier based on auto correction feedback for biomedical systems

Design of a novel CMOS instrumentation amplifier using 90 nm technology

A Compact Sub-μW CMOS ECG Amplifier With 57.5-MΩ Zin, 2.02 NEF, 8.16 PEF and 83.24-dB CMRR

Research and Design of Wide Input Common-Mode Range Current-Sense Amplifier

A 0.6V 119 dB High-CMRR Low-NEF PGA with common-mode voltage control for ECG recording

A CMOS High-Speed Multistage Preamplifier for Comparator Design

A 20 Μw Dual-Channel Analog Front-End in 65nm CMOS for Portable ECG Monitoring System

Micro-Power Low-Offset Instrumentation Amplifier IC Design for Biomedical System Applications

100.5 dB SNDR Analog Front-End With a Resistor-Based Discrete-Time Delta-Sigma Modulator for Eliminating Switching Noise and Harmonics

Design of High-Side Current Sense Amplifier with Ultra-Wide ICMR