Abstract:This paper introduces a compact picosecond laser system using tapered double cladding fiber-single crystal fiber hybrid amplification technology for the first time. By modifying the Ginzburg-Landau equation, we established a simulation model and designed a passive mode-locked picosecond oscillator based on a semiconductor saturable absorber mirror. The oscillator outputs laser with a pulse width of 7.75 ps, a center wavelength of 1030.55 nm, and a spectrum width of 0.58 nm. The seed laser is stretched and amplified by the all-fiber front stage, and then injected into the tapered double cladding fiber-single crystal fiber hybrid amplifier. The laser power is amplified from 820 mw to 103.1 W, obtaining a gain of 21 dB. We used zero-phonon line pumping technology in single crystal fiber amplifier to reduce the thermal effects caused by quantum loss, thereby increasing the length of the crystal and increasing the power loading capacity. We designed a single crystal fiber amplification module using Yb:YAG with 60 mm long, 1 mm diameter and a 1 at.% doping rate for the first time. Finally a hundred-watt level picosecond laser output with a repetition frequency of 26.33 MHz, an average power of 103.1 W, a pulse width of 244.72 ps, a spectrum width of 1.16 nm, and a beam quality of M2 x = 1.368 and M2 y = 1.511 was obtained. To the best of our knowledge, this is the highest picosecond laser output power for an all-fiber front-stage combined with a single-stage single crystal fiber amplifier.

High-Energy Hundred-Picosecond Hybrid Fiber And Solid-State Laser Amplifier System For Laser-Induced Damage Application

High-energy hundred-picosecond fiber-solid hybrid laser and its application in laser-induced damage in PIN photodiode

Fiber-solid, Hybrid, Single-Frequency Laser (100 W) with a 100 MHz Repetition Rate and 1 Ns Pulse Width from a Spherical Aberration Compensated Four-Stage Nd:YVO4 Amplifier

Laser-induced Damage in a Silicon-Based Photodiode by MHz Picosecond Laser

High Peak Power Picosecond Hybrid Fiber and Solid-State Amplifier System

High Peak Power and High Beam Quality Fiber-Solid Hybrid Amplification Laser System

100 MW Peak Power Picosecond Laser Based on Hybrid End-Pumped Nd:YVO4 and Side-Pumped Nd:YAG Amplifiers

Compact hundred-watt level picosecond laser system based on tapered double cladding fiber-single crystal fiber hybrid amplifier

Hundred Nano-Joules Polarization-Maintaining Yb-Doped Fiber Femtosecond Laser Amplification System

Nanosecond-pulse High-Peak-power Circle-Focusing Laser Beam for Laser Processing

A 12 Mj 11 Ns Spectrally Narrow Fiber Amplifier with A Pulsed Pump

Picosecond Nd:YLF Five-Passes Laser Amplifier with 20 Mj Pulse Energy

95-Ps All-Solid-state Laser with a Low-Power Microchip Laser Seed and a Two-Stage Single-Pass Bounce Geometry Amplifier

670 Kw Nanosecond All-Fiber Super-Irradiation Pulsed Amplifiers at High Repetition Rates

An efficient high-power femtosecond laser based on periodic-layered-Kerr media nonlinear compression and a Yb:YAG regenerative amplifier

High energy single-frequency double-pulse hybrid MOPA system

Hundreds of picosecond pulses amplifier based on Yb-doped tapered fiber for the generation of 100 W average output power

All-Fiber Millijoule Energy and Nanoseconds Pulse Operation of A High Beam Quality Multi-Stage Pulse-Pumped Yb-Doped Amplifier Cascade

High Energy (100 Mj) and High Peak Power (8 MW) Nanosecond Pulses Delivered by Fiber Lasers and Self-Focusing Analysis Based on a Novel Mode Decomposition Method

Fiber Phase Conjugation in Laser Diode-Pumped,Electrooptical Q-Switched Laser with Double-Pass Amplifier

112-Μj 180-Fs Pulses at 1-Khz Repetition Rate from Yb-Doped Laser Based on Strictly All-Fiber CPA Structure