Abstract:Microwave communication systems are being developed with the goal to achieve miniaturization and high reliability. There are urgent requirements for microwave dielectric materials to exhibit low sintering temperatures, excellent microwave dielectric properties, and prominent mechanical performance. However, simultaneously achieving these requirements is a significant challenge. These concerns have been addressed in the uniform ultra-fine-grained 0.95MgTiO3–0.05CaTiO3 ceramics with an average grain size of ~0.5 μm via a grain size engineering strategy. Interestingly, the sintering temperature in the unique two-step sintering method of 1250°C/1 min and 1130°C/10 h is much lower (200°C–300°C) than that obtained in the conventional sintering method reported previously (1400°C–1450°C). Excellent dielectric properties are achieved, with relative permittivity εr = 20.11, quality factor Q×f = 68,613 GHz, and temperature coefficient of resonant frequency τf = +1.81 ppm/°C. The bending strength σf, Vickers hardness Hv, and elastic modulus E reach up to 212.4 MPa, 10.1 GPa, and 200.7 GPa, respectively. These values are significantly enhanced over those of samples obtained via the conventional sintering method with an average grain size of ~2.5 μm. For the first time, uniform ultra-fine-grained microwave dielectric materials with excellent microwave dielectric properties and prominent mechanical performance were synthesized. This work provides a guideline for developing other high-performance microwave dielectric materials and makes a significant contribution to the miniaturization and high reliability of microwave dielectric devices.

High Permittivity and Low-Loss Millimeter-wave Dielectric Ceramics

Low-temperature Co-Fired Ceramics with High Thermal Expansion and Reliability for Millimeter-Wave Antennas

Unleashing the Potential of Mg2SiO4-based Ceramics for Millimeter-Wave Applications: Achieving Ultra-Low Loss with Enhanced Temperature Stability Through Heterovalent Ion Substitution

High Permittivity and Low Loss Microwave Dielectrics Suitable for 5G Resonators and Low Temperature Co-Fired Ceramic Architecture

Low temperature sintered MgO–based microwave dielectric ceramics with ultra‐low loss and high thermal conductivity

Low-loss dielectric ceramic materials and their properties

A New Microwave Ceramic with Low-Permittivity for Ltcc Applications

Lattice Dynamics and Terahertz Response of Microwave Dielectrics: A Case Study of Al-doped Ca0.6Sm0.27TiO3 Ceramics

Ultra low loss (Mg 1 − x Ca x ) 2 SiO 4 dielectric ceramics (x = 0 to 0.15) for millimeter wave applications

Low permittivity cordierite-based microwave dielectric ceramics for 5G/6G telecommunications

Ultra Low Loss (mg1 − Xcax)2sio4dielectric Ceramics (x = 0 to 0.15) for Millimeter Wave Applications

Li4Mg3Ti2O9: A novel low-loss microwave dielectric ceramic for LTCC applications

Silicate dielectric ceramics for millimetre wave applications

Grain Size Engineered 0.95mgtio3–0.05catio3 Ceramics with Excellent Microwave Dielectric Properties and Prominent Mechanical Performance

High-Qf value and temperature stable Zn2+-Mn4+ cooperated modified cordierite-based microwave and millimeter-wave dielectric ceramics

Modified poly(phenylene oxide)/(CaSr)TiO 3 composites with ultrahigh permittivity and low loss for microwave substrates

Grain size engineered 0.95MgTiO 3 –0.05CaTiO 3 ceramics with excellent microwave dielectric properties and prominent mechanical performance

MgF 2 -based microwave dielectric ceramics with ultra-low sintering temperature and high thermal expansion coefficient

HIGH DIELECTRIC PROPERTIES OF LOW-TEMPERATURE SINTERED (Ca0.5Cu0.5)TiO3 CERAMICS

Low-permittivity BaCuSi4O10-based Dielectric Ceramics: an Available Solution to Connect Low Temperature Cofired Ceramic Technology and Millimeter-Wave Communications

Low dielectric loss ceramics in the Mg4Nb2O9-ZnAl2O4-TiO2 ternary system