Absolute Efficiency Of A Phi-76mm-X-100mm Bgo Scintillation Detector

X Liu,Yl Ye,Dx Jiang,Xt Lu,Ht Liu

1994-01-01

Abstract:Using monoenergetic gamma-ray generated from low energy (p,gamma) resonant reactions, the full-energy-peak gamma-ray detecting efficiency of a phi 76mm x 100mm BGO scintillating detector was measured. The efficiencies of 7%, 9% and 22% are obtained at gamma energies of 17.65, 17.23 and 6.13 MeV, respectively.

What problem does this paper attempt to address?

Energy Response of a Φ76 Mm X 100 Mm BGO Scintillation Detector for Gamma-Rays below 20 MeV

Xin Liu,Ye Yanlin,Jian Dongxing,Lu Xiting,Hongtao Liu

1993-01-01

Abstract:A 76 mm-diameter by 100 mm-long BGO scintillation detector is assembled to detect the highenergy gamma-rays produced from intermediate energetic heavy-ion nuclear reaction. The energyresponse of the detector is studied in the incident gamma-rays energy range of 0.661 MeV to17.65 MeV, the monoenergetic gamma-rays are generated by radiative sources and several lowenergy (p, γ) resonant nuclear reactions. The response function is obtained by delicate datefitting. The full energy peak energy resolution is 14.2% at 0.661 MeV and 4.1% at 17.65MeV, respectively. One analyzing method of the energy spectra of high energy gamma-rays is al-so discussed in the paper.
PERFORMANCE OF A 76-MM BY 100-MM BGO DETECTOR

YL YE,X LIU,DX JIANG,XT LU,HT LIU,JS LIN,CC ZHOU

1992-01-01

Chinese Physics

Abstract:A large cylindrical BGO detector is constructed for measuring high-energy gamma-rays in intermediate-energy heavy-ion reactions using crystals and photomultipliers made in China. The light-collection method, relative light yield of the crystal, and the ability to resolve energy and time are reported here. The effectiveness of the detector with different photomultipliers is checked and the possibilities of using such a detector in experiments are discussed.
Performance Results of BGO Block Detectors Based on Flat Panel PS-PMT for PET

Huafeng Liu,Qiang Zhao,Pengcheng Shi

DOI: https://doi.org/10.1109/TNS.2007.901231

IF: 1.703

2007-01-01

IEEE Transactions on Nuclear Science

Abstract:We have developed a new detector composed of a 20times20 array of 2times2times20 mm3 Bi4Ge3O12 (BGO) scintillators and a novel flat panel position sensitive photomultiplier tube(FP-PS-PMT) - Hamamatsu R8400-00-M256. The performance of the block detector was evaluated in terms of applicability to positron emission tomography (PET). The energy resolution was about 23% FWHM for 511 keV gamma-rays. Th...
The full-energy peak efficiency of gamma-ray spectrometry by numerical calculation method

Jian Zhang,Qingxian Zhang,Wanchang Lai,Weicheng Li,Xian Guan,Zikun Li,Maolin Xiong,Zhiqiang Cheng,Heyi Tan,Xiaozhe Li,HeXi Wu,Liangquan Ge

DOI: https://doi.org/10.1016/j.nima.2024.169145

2024-02-09

Abstract:The full-energy peak efficiency allow radioactivity determination in gamma-ray spectrometry. In the determination of the full-energy efficiency, numerical calculation method has been widely used because of its accessibility, stability, and low computational cost. The current study presents a new direct numerical method that is based on the determining of the total efficiency and the escape efficiency. The method provides a detailed description of the generation and escape of secondary photons from the sensitive volume. It is applicable to any source-detector geometry and also considers the self-attenuation of the source matrix and the attenuation caused by absorber layers between the source and the sensitive volume. The results of comparing the new numerical method with experimental measurement for the point source test model demonstrate relative errors within −2.73∼5.57 %, indicating the high reliability of this new method for sourceless efficiency calibration.

physics, particles & fields, nuclear,nuclear science & technology,instruments & instrumentation
Development of a New Γ-Ray Detector for PEM Applications

Zhao Qiang,Tian Yi,Liu Hua-Feng

DOI: https://doi.org/10.3321/j.issn:0254-3052.2007.05.017

2007-01-01

Abstract:We are developing a high specificity detector for detecting the increased metabolic rate of breast tumors. Positron emission mammography (PEM) provides a highly efficient, high spatial resolution positron imaging system. PMT plays a very important role in PEM detectors, because most of the systems consist of scintillator arrays coupled with PMT. Our detector is composed of 20×20 arrays of 2mm×2mm×20mm of Bi4Ge3O12 (BGO) scintillators and a novel flat panel position-sensitive PMT (FP-PS-PMT) -Hamamatsu R8400-00-M256. Spatial resolutions of 2.0mm FWHM and energy resolutions of 23% FWHM are achieved.
Nonproportionality in the scintillation light yield of bismuth germanate

T. R. Gentile,M. J. Bales,H. Breuer,T.E. Chupp,K. J. Coakley,R. L. Cooper,J. S. Nico,B. O'Neill

DOI: https://doi.org/10.1016/j.nima.2014.11.002

2015-05-01

Abstract:We present measurements of nonproportionality in the scintillation light yield of bismuth germanate (BGO) for gamma-rays with energies between 6 keV and 662 keV. The scintillation light was read out by avalanche photodiodes (APDs) with both the BGO crystals and APDs operated at a temperature of approximately 90 K. Data were obtained using radioisotope sources to illuminate both a single BGO crystal in a small test cryostat and a 12-element detector in a neutron radiative beta-decay experiment. In addition one datum was obtained in a 4.6 T magnetic field based on the bismuth K x-ray escape peak produced by a continuum of background gamma rays in this apparatus. These measurements and comparison to prior results were motivated by an experiment to study the radiative decay mode of the free neutron. The combination of data taken under different conditions yields a reasonably consistent picture for BGO nonproportionality that should be useful for researchers employing BGO detectors at low gamma ray energies.

Instrumentation and Detectors,Nuclear Experiment
A BGO detector unit for a stationary high resolution positron emission tomograph

S Yamamoto,S Miura,H Iida,I Kanno

DOI: https://doi.org/10.1097/00004728-198609000-00028

Abstract:A new encoding scheme was developed that is applicable to bismuth germanate (BGO) detector units for a high resolution positron emission tomograph. The detector unit is composed of eight equal-size, 3 mm wide BGO crystals coupled to a dual-module square photomultiplier tube (PMT) through a pair of light guides. The light guides divide the scintillation light between the two modules of the PMT, with a ratio dependent on the crystal of origin. Mean detector pair spatial resolution as measured by the point spread function was 3.9 mm full width at half maximum (FWHM) and reconstructed image spatial resolution was 4.8 mm FWHM at the center of the field of view. Timing resolution between two detector units was 6.0 ns FWHM. Energy resolution was 24% FWHM for 511 keV gamma rays. The finest spots of the Derenzo phantom were clearly resolved.
Gamma ray registration efficiency simulation of a HPGe detector with PHITS

A. Bagramova,K. Zhumadilov,S. Endo,T. Kajimoto,A. Sakaguchi,Zh Zeinulla,M. Hoshi

DOI: https://doi.org/10.1007/s10967-024-09839-2

2024-10-26

Journal of Radioanalytical and Nuclear Chemistry

Abstract:Simulation of the detector response to determine the detection efficiency as a function of gamma-ray energies makes it possible to avoid the efficiency calibration when this process is difficult for some reasons. In this study, full energy peak efficiencies of gamma-rays for a high-purity germanium (HPGe) detector have been calculated. A geometry consisted of the HPGe detector and a volume source was constructed by using PHITS. The energy deposition to the HPGe was calculated for γ rays generated in the source. The full energy peak efficiency was estimated from counts of the full energy peak on the deposition distribution. The results obtained by PHITS simulations were validated by comparing with measured efficiencies (88–1836 keV) obtained from actual measurements of a nine-nuclide mix-standard source. The overall discrepancy between the simulated and measured data showed a maximum of 3.7% difference, which means with this method, the efficiency of gamma-ray detection by HPGe detector could be determined with a certain degree of certainty even in the absence of a standard sample.

chemistry, inorganic & nuclear, analytical,nuclear science & technology
Efficiency Measurement of NaI(Tl) Detector for a Long Tube Volume Source of 6.13mev Gamma-Ray

ZR Shi,K Xu,SY Ding,SQ Wang,ZR Guo,LZ Zuo

DOI: https://doi.org/10.3321/j.issn:0254-3052.2005.02.005

2005-01-01

Abstract:The relation of the N-16 leak rate of the nuclear reactor to the efficiency and counting rate of gamma-ray detector, velocity of high pressure vapor, is deduced. A conclusion of the efficiency independent on the velocity of high pressure vapor and decay constant of N-16 is drawn. Experimentally the space distribution of the relative efficiencies and the absolute efficiency at a reference point are measured with PuC source emiting 6.13 MeV gamma ray detected by NaI(Tl) counter. The measured efficiency is consistent with Monte Carlo calculation in 7%. The Compton small angle scattering contribution to the convergence length and the effect of the energy difference between 7.12 MeV and 6.13 MeV gamma ray on measured N-16 leak rate are discussed.
A New Method for High-Energy Pulsed Gamma Measurement Within Intense Background X-Rays

Tan Xin-Jian,Ouyang Xiao-Ping,Wang Qun-Shu,Song Zhao-Hui,Kang Ke-Jun,Xia Liang-Bin

DOI: https://doi.org/10.1088/1674-1056/19/1/010703

2010-01-01

Abstract:The accelerator-generating 6.13 MeV pulsed Gamma by 19 F（p, αγ） 16 O reaction usually synchronizes with an intense bremsstrahlung x-ray which has a maximum energy of 1 MeV. This paper proposes a new method, named the scattering and absorbing method, to diagnose the 6.13 MeV Gamma. This method includes two parts: the detector and a scatterer placed in front of the detector. The detector converts the Gamma to electrons and then collects the electrons by a scintillator. In order to restrain the interference of the low-energy background, the scintillator collects the electrons at a small angle. The scintillator is wrapped with electro-absorbing material to absorb the low-energy electrons generated by background x-rays. The theoretical sensitivity ratio of 6.13 MeV Gamma to 1 MeV x-rays is greater than 150. The scatterer is a pretreatment tool to scatter some background x-rays away from the radial beam before they enter the detector. By varying the length, the scatterer can reduce the background x-rays to an acceptable level for the detector.
Calculation of efficiency and resolution of a hexagonal NaI(Tl) detector as a function of source position

A. Hamzawy,M.S. Badawi,I.N. Ruskov,D.N. Grozdanov,M.I. Badawi,A.A. Thabet,Yu.N. Kopatch,N.A. Fedorov,B.A. Salem,TANGRA collaboration

DOI: https://doi.org/10.1088/1748-0221/19/07/t07003

2024-07-13

Journal of Instrumentation

Abstract:Most gamma-ray scintillation detectors currently in use are made from inorganic materials that have a relatively high electron density. Quite often they are used to build multidetector systems that provide high scintillation light output. The performance of a gamma radiation detector (its detection efficiency) depends on the shape and size of the crystal, as well as on the source-to-detector geometry used. The NaI(Tl) gamma detector exhibits moderate energy resolution but relatively high gamma-ray detection efficiency and fast time response. In this work, the efficiency and resolution of a scintillation hexagonal detector are studied to optimize its response function. This type and size of scintillator were selected to construct a budget-friendly, reconfigurable, easy-to-maintain multidetector system for registering gamma-rays following fission, capture, and inelastic neutron scattering reactions, with reasonably good energy and time resolutions The research results made it possible to establish a geometric solid angle that increases the efficiency of recording gamma-ray radiation of the hexagonal NaI(Tl) scintillation probe under study.

instruments & instrumentation
A method to measure the quenching factor for recoil energy of oxygen in bismuth germanium oxide scintillators

Yuga Ommura,Hiroshi Ito,Takatomi Yano,Akihiro Minamino,Masaki Ishitsuka

DOI: https://doi.org/10.1088/1748-0221/18/04/T04006

2023-04-27

Abstract:Bismuth germanium oxide ($\rm Bi_{4} Ge_{3} O_{12}$, BGO) scintillation crystals are widely used as detectors in the fields of particle physics and astrophysics due to their high density, and thus higher efficiency for gamma-ray detection. Owing to their good chemical stability, they can be used in any environment. For rare-event searches, such as dark matter and coherent elastic neutrino-nucleus scattering, BGO crystals are essential to comprehend the response of nuclear recoil. In this study, we have analyzed the events of neutron elastic scattering with oxygen in BGO crystals. Then, we have measured the quenching factor for oxygen recoil energy in the BGO crystal as a function of recoil energy by using a monoenergetic neutron source.

Instrumentation and Detectors,Instrumentation and Methods for Astrophysics,High Energy Physics - Experiment
HPGe Detector Efficiencies for Extended Sources Using the Monte Carlo Method

Waseem Khan,Chaohui He,Yu Cao

DOI: https://doi.org/10.1080/10420150.2019.1619733

2019-01-01

Radiation Effects and Defects in Solids

Abstract:To determine the activity of radioactive sources, accurate efficiencies are always required since the data provided by the manufacturer for detector model is insufficient to calculate the efficiencies value and obtained strong discrepancies between simulated and experimental results, especially for low photon energies. For this purpose, a detailed detector model was developed to simulate the total and full energy peak efficiencies of a p-type coaxial High Purity Germanium (HPGe) detector using GEANT4. In the simulation, gamma aqueous sources containing several radionuclides were used, covering the energy range from 59.50 to 1836.01 keV. In the case of extended sources, the coincidence summing correction factors () for two nuclides () were calculated from the peak () and total efficiencies () at 15 points throughout the source volume obtained with GEANT4. A modified detector model including the summing effect, the simulated full energy peak efficiencies agreed with the experimental values within 1%, except for the high energy range where they are less than 2% between 122 and 1836keV for the small extended source volume.
Measurement of the Gamma-Ray Sensitivity and Signal-to-noise Ratio of a New Scattered-Electron Detector

Liangbin Xia,Xiaoping Ouyang,Qunshu Wang,Kejun Kang,Xinjian Tan

DOI: https://doi.org/10.1063/1.2976670

2008-01-01

Abstract:A new detector suitable for measuring high intensity pulsed gamma-ray sources and based upon scattered-electron method is proposed. The detector has a relatively flat energy response in the range of 0.4-5 MeV and works in current mode. The performances of the detector under several conditions were studied by Monte Carlo simulation using the MCNP code. A comparison between calculations and measurements performed using the 1.25 MeV line of Co-60 is also addressed. The experimental signal produced by the detector was thus studied and decomposed into its main components in order to establish the signal-to-noise ratio (SNR). The latter is compared to SNR calculated for other type of detectors.
Detection Efficiency Calculations Using Geant4 for a Broad-Energy Germanium Gamma Spectrometer

Chuanlei Liu,Kurt Ungar,Dylan Pierce,Ian Hoffman,Weihua Zhang

DOI: https://doi.org/10.1007/s10967-017-5239-5

2017-01-01

Journal of Radioanalytical and Nuclear Chemistry

Abstract:In assistance of radionuclide measurements at Canada’s Comprehensive Nuclear-Test-Ban Treaty (CTBT) laboratory, a Geant4 Monte Carlo application has been developed in simulating a broad-energy germanium detector and calculating detection efficiencies. The detector model was optimized in a reliable and non-biased manner through simultaneous tuning on gap distance and detector dimension, and was validated over various realistic measurement scenarios. All work is based on a series of experiments which covers the typical energy range of gamma radiation in environmental analysis, and considers the variety of the CTBT sample type, dimension and distance-to-detector. In all cases, the predicted efficiencies are consistent with the empirical ones within 5%, with a typical deviation of 3% in majority.
Effect of detector geometry and surface finish on Cerenkov based time estimation in monolithic BGO detectors

Jens Maebe,Stefaan Vandenberghe

DOI: https://doi.org/10.1088/1361-6560/acabfd

2023-01-05

Abstract:Objective.Time-of-flight positron emission tomography based on bismuth germanate (BGO) detectors is made possible due to fast emission of Cerenkov light. Only around 17 Cerenkov photons are produced per 511 keV photoelectric event, making high photon collection efficiency crucial for obtaining good time-of-flight capabilities. In this study, we investigate how different lateral and back surface finishes affect the photon collection efficiency and Cerenkov based timing performance in monolithic BGO.Approach.The study is performed using GATE for gamma and optical photon modeling, with surface reflections of photons simulated by the LUT Davis model. We compare for different detector configurations (regarding size and surface finishes) the photon collection efficiency, detection delays of the first few optical photons and coincidence time resolution estimations obtained by modeling the SiPM signals and performing leading edge discrimination. An additional comparison is made to LYSO scintillators and pixelated detectors.Main results.Although Cerenkov photon emission is directional, many high incidence angle Cerenkov photons are emitted due to electron scattering in the crystal. Substituting a polished back (photodetector side) surface for a rough surface increases the collection efficiency of these high angle of incidence photons. Results show that for a monolithic 50 × 50 × 12 mm3BGO detector with reflective side surfaces, this leads to an overall increase in photon collection efficiency of 34%. Cerenkov photon collection efficiency is also improved, resulting in a reduction of the photon detection delays (and the variation therein) of the first few optical photons. This leads to a better coincidence time resolution, primarily achieved by a shortening of the tails in the time-of-flight kernel, with an 18% reduction in full width at tenth maximum.Significance.This study shows the importance of the photon collection efficiency for timing performance in Cerenkov based monolithic detectors, and how it can be improved with different surface finishes.
Scintillation Detector Design Study for Prompt Gamma Photon Detection in Proton Therapy Monitoring

Hongyang Zhang,Peng Fan,Tianpeng Xu,Qingyang Wei,Tianyu Ma,Yaqiang Liu,Zhaoxia Wu

DOI: https://doi.org/10.1109/nssmic.2017.8532768

2017-01-01

Abstract:Proton therapy is currently one of the most advanced radiotherapy technologies. However, due to proton range uncertainty during proton dose delivery, proton range monitoring is of vital importance for proton therapy. In recent years, there has been increased interest of utilizing prompt gamma imaging (PGI) for online proton range monitoring due to its high yield, real-time emission property and immunity to biological wash-out effect. However, the 2 ~ 8 MeV high energy of prompt gamma makes detector design of PGI system challenging and the saturation effect of SiPM, which is a kind of commonly used photodetector in scintillation detector design, should be carefully considered. In this work, we propose a scintillation detector design based on BGO crystal and SiPM (SensL FJ30035) for the PGI system we are now developing. A numerical simulation considering the optical photon generation and single microcell response of SiPM pixel was performed to evaluate the saturation of SiPM under the proposed detector design and compared with that based on LYSO crystal. The results demonstrate that BGO-based detector design features similar detector efficiency but significantly reduced saturation effect of SiPM compared with LYSO-based detector design for high energy prompt gamma detection. A detector module consisting of a 12 × 12 BGO block (single crystal size: 3.5 × 3.5 × 30 mm3) and an 8 × 8 SiPM array was further developed and an experiment platform was set up to evaluate the detector performance in terms of 2D flood map and energy resolution under 22Na source irradiation. In the 2D flood map, each crystal element can be clearly identified, indicating good positioning capability of the proposed detector design. The energy resolution of the proposed detector design is 16.4 ± 1.4 % for 1275 keV gamma photons. Based on these initial results, we conclude the proposed detector has high detection efficiency, negligible SiPM saturation, good positioning capability and reasonable energy performance and is feasible for prompt gamma detection.
Efficiency Calibration of a Large-Area Neutron Detector by Using Am/Be Neutron Source

QY Hu,YL Ye,ZH Li,XQ Li,DX Jiang,T Zheng,QJ Wang,H Hua,CE Wu,ZQ Chen,J Ying,DY Pang,GL Zhang,J Wang

DOI: https://doi.org/10.1109/tns.2004.842725

IF: 1.703

2005-01-01

IEEE Transactions on Nuclear Science

Abstract:Neutron detection efficiency for a long wedge-shaped plastic scintillation detector was measured by using the Am/Be neutron source. The overall efficiency attains 23% at around 2 MeV and decreases to 15% at about 5 MeV. The experimental results are in agreement with the Monte Carlo simulation calculations.
Detector Development for Prompt Gamma Imaging in Proton Therapy Online Monitoring

Hongyang Zhang,Peng Fan,Shi Wang,Yan Xia,Tianpeng Xu,Qingyang Wei,Zhaoxia Wu,Yaqiang Liu,Tianyu Ma

DOI: https://doi.org/10.1109/nssmic.2018.8824761

2018-01-01

Abstract:Proton therapy allows for accurate positioning of target tumors by accurate dose delivery at the Bragg peak. But a 10~15 mm proton range deflection could be caused by uncertainties including CT image artifacts and treatment setup errors. Prompt gamma imaging (PGI) offers a reliable real-time monitoring for proton range inside the patient and more accurate spatial information of the Bragg peak. In this work, we report the detector development for a prompt gamma imaging system. A detector based on a 12 × 12 BGO block and an 8 × 8 SiPM array was designed. Since 2~8 MeV high energy of prompt gamma may cause complicated interaction inside scintillation crystal and saturation of SiPMs, positioning performance and response linearity of the detector were evaluated. The proposed detector was tested under high energy sources, such as 22 Na, 88 Y and 232 Th. Flood maps at 511 keV and 1.275 MeV of 22 Na, 898 keV and 1.836 MeV of 88 Y and 2.6 MeV of 232 Th were generated. Root mean squared (RMS) metric were defined to assess the detector's positioning performance quantitively. Detector response linearity at different energy were evaluated. The detector demonstrates better crystal identification at higher energy. Energy resolution of 36.21% ± 5.16% (511 keV), 28.24% ± 3.86% (898 keV), 20.56% ± 2.46% (1.275 MeV), 17.48% ± 2.63% (1.836 MeV) and 17.08 ± 3.08% (2.6 MeV) were reached respectively. Moreover, mean linearity of peak positions within 144 single crystals was 0.9997 ± 0.00046 which is a clear demonstration of good detector response linearity. The result shows that the detector performed well on positioning, energy resolving and response linearity. Decreased RMS value and energy resolution implies even better positioning performance and energy resolving ability at 2~8 MeV.
Performance of Dual-Ended Readout PET Detectors Based on BGO Arrays and BaSO4 Reflector

Junwei Du

DOI: https://doi.org/10.1109/trpms.2021.3096534

Abstract:In this paper, the performance of two dual-ended readout PET detectors based on 15 × 15 BGO arrays were compared. The crystal elements of one BGO array have polished lateral surfaces, while the crystal elements of the other BGO array have unpolished lateral surfaces. The two ends of the BGO elements are polished. The two BGO arrays both have a pitch size of 1.6 mm and thickness of 20 mm, and BaSO4 with a thickness of 80 μm was used as the reflector. Hamamatsu S14161-0305-08 SiPM arrays were used as photodetectors. All the measurements were performed at a bias voltage of 41.0 V and a temperature of 23.5 °C. The flood histograms show that all the crystal elements in the two BGO arrays were clearly resolved. The detector based on the BGO array with polished lateral surfaces provides an energy resolution of 16.9 ± 1.3%, timing resolution of 3.2 ± 0.2 ns, and DOI resolution of 18.4 ± 2.2 mm. In comparison, the detector based on the BGO array with unpolished lateral surfaces provides an energy resolution of 17.7 ± 2.0%, timing resolution of 3.5 ± 0.3 ns, and DOI resolution of 3.2 ± 0.2 mm.

Absolute Efficiency Of A Phi-76mm-X-100mm Bgo Scintillation Detector

Energy Response of a Φ76 Mm X 100 Mm BGO Scintillation Detector for Gamma-Rays below 20 MeV

PERFORMANCE OF A 76-MM BY 100-MM BGO DETECTOR

Performance Results of BGO Block Detectors Based on Flat Panel PS-PMT for PET

The full-energy peak efficiency of gamma-ray spectrometry by numerical calculation method

Development of a New Γ-Ray Detector for PEM Applications

Nonproportionality in the scintillation light yield of bismuth germanate

A BGO detector unit for a stationary high resolution positron emission tomograph

Gamma ray registration efficiency simulation of a HPGe detector with PHITS

Efficiency Measurement of NaI(Tl) Detector for a Long Tube Volume Source of 6.13mev Gamma-Ray

A New Method for High-Energy Pulsed Gamma Measurement Within Intense Background X-Rays

Calculation of efficiency and resolution of a hexagonal NaI(Tl) detector as a function of source position

A method to measure the quenching factor for recoil energy of oxygen in bismuth germanium oxide scintillators

HPGe Detector Efficiencies for Extended Sources Using the Monte Carlo Method

Measurement of the Gamma-Ray Sensitivity and Signal-to-noise Ratio of a New Scattered-Electron Detector

Detection Efficiency Calculations Using Geant4 for a Broad-Energy Germanium Gamma Spectrometer

Effect of detector geometry and surface finish on Cerenkov based time estimation in monolithic BGO detectors

Scintillation Detector Design Study for Prompt Gamma Photon Detection in Proton Therapy Monitoring

Efficiency Calibration of a Large-Area Neutron Detector by Using Am/Be Neutron Source

Detector Development for Prompt Gamma Imaging in Proton Therapy Online Monitoring

Performance of Dual-Ended Readout PET Detectors Based on BGO Arrays and BaSO4 Reflector