Abstract:Time-of-flight (TOF) positron emission tomography (PET) detectors improve the signal-to-noise ratio of PET images by limiting the position of the generation of two 511 keV gamma-rays in space using the arrival time difference between the two photons. Unfortunately, bismuth germanate (BGO), widely used in conventional PET detectors, was limited as a TOF PET scintillator due to the relatively slow decay time of the scintillation photons. However, prompt Cerenkov light in BGO has been identified in addition to scintillation photons. Using Cerenkov photons for timing has significantly improved the coincidence timing resolution (CTR) of BGO. Based on this, further research on improving the CTR for a BGO-based TOF PET system is being actively conducted. Wrapping materials for BGO pixels have primarily employed white reflectors to most efficiently collect scintillation light. White reflectors have customarily been used as reflectors for BGO pixels even after Cerenkov light began to be utilized for timing calculations in pixel-level experiments. However, when the arrival-time differences of the two 511 keV annihilations photons were measured with pure Cerenkov radiators, painting the lateral sides of the radiators black can improve CTR by suppressing the reflection of Cerenkov photons. The use of BGO for TOF PET detectors requires simultaneously minimizing scintillation loss for good energy information and suppressing reflected Cerenkov photons for better timing performance. Thus, reflectors for BGO pixels should be optimized for better timing and energy performance. In this study, colored polytetrafluoroethylene (PTFE) tapes with discontinuous reflectance values at specific wavelengths were applied as a BGO reflector. We hypothesized that CTR could be enhanced by selectively suppressing reflected Cerenkov photons with an optimum colored reflector on the BGO pixel while minimizing scintillation photon loss. CTRs were investigated utilizing white and three colors (yellow, red, and green) PTFE tapes as a reflector. In addition, black-painted PTFE tape and enhanced specular reflector film were investigated as reference reflector materials. When 3 × 3 × 20 mm3BGO pixels were wrapped with the yellow PTFE reflector, the CTR was significantly improved to 365 ± 5 ps from 403 ± 14 ps measured with the conventional white PTFE reflector. Adequate energy information was still obtained with only 4.1% degradation in light collection compared to the white reflector. Colored reflectors show the possibility to further improve CTR for BGO pixels with optimum reflectance design.

Effect of detector geometry and surface finish on Cerenkov based time estimation in monolithic BGO detectors

Dual-ended readout of bismuth germanate to improve timing resolution in time-of-flight PET

Pushing the limit of BGO-based dual-ended Cherenkov PET detectors through photon transit time correction

BGO as a hybrid scintillator / Cherenkov radiator for cost-effective time-of-flight PET

Electronics method to advance the coincidence time resolution with bismuth germanate

On timing-optimized SiPMs for Cherenkov detection to boost low cost time-of-flight PET

Improvement of light coupling in BGO detector module by optimization of the crystal shape

Emphasizing Cherenkov photons from bismuth germanate by single photon deconvolution

Colored reflectors to improve coincidence timing resolution of BGO-based time-of-flight PET detectors

Exploring Scintillators and Cherenkov Radiators for MIP Timing Detectors

Collection of scintillation light from small BGO crystals

Advances in heterostructured scintillators: toward a new generation of detectors for TOF-PET

Segmented readout for Cherenkov time-of-flight positron emission tomography detectors based on bismuth germanate

Performance comparison of dual-ended readout depth-encoding PET detectors based on BGO and LYSO crystals

Optimization Of Crystal Surface Treatment For A Double Layer Depth Of Interaction Detector

Study of optical reflectors for a 100ps coincidence time resolution TOF-PET detector design

Nanocrystalline Lead Halide Perovskites to Boost Time‐of‐Flight Performance of Medical Imaging Detectors

Performance of Dual-Ended Readout PET Detectors Based on BGO Arrays and BaSO4 Reflector

Optimisation of monolithic nanocomposite and transparent ceramic scintillation detectors for positron emission tomography

A BGO detector unit for a stationary high resolution positron emission tomograph

Optimization of a Scintillation Detector for Positron Emission Tomography