Abstract:This paper describes a test program on the stress concentration factors (SCFs) of stainless steel hybrid tubular (SSHT) joints with square hollow section (SHS) braces and circular hollow section (CHS) chord and SSHT joints with CHS braces and SHS chord. The load was applied to the brace for all test specimens. Twenty specimens in total, including ten overlapped and ten gapped tubular K-joints, were tested. Different geometric parameters were used which include brace width-to-chord diameter ratio (beta(1) = b(1)/d(0)), brace-to-chord thickness ratio (tau(1) = t(1)/t(0)) and chord diameter-to-thickness ratio (2 gamma(1) = d(0)/t(0)) for SHS-to-CHS hybrid tubular joints, brace diameter to-chord width ratio (beta(2) = d(1)/b(0)), brace-to-chord thickness ratio (tau(2) = t(1)/t(0)) and chord width-to-thickness ratio (2 gamma(2) = b(0)/t(0)) for CHS-to-SHS hybrid tubular joints. A number of strain gauges were used at the hot spot locations for various tubular joints. The hot spot stress (HSS) method was used to determine the SCFs of SSHT joints using the quadratic extrapolation method. This was a consequence of the stress distributions around the intersection area of SHS-to-CHS and CHS-to-SHS hybrid tubular joints being nonlinear. Results found the maximum SCFs for hybrid overlapped tubular K-joints with square braces and circular chord to be located at the hot spot location at an angle of 135 degrees between the SHS brace and the CHS chord. This is characterized as line A. The maximum SCFs of hybrid gapped tubular K-joints with square braces and circular chord were located at the hot spot location at an angle of 45 degrees between the SHS tension brace and the CHS chord (characterized as line C) and at an angle of 45 degrees between the SHS compression brace and the CHS chord (characterized as line E). The maximum SCFs of hybrid overlapped tubular K-joints with circular braces and square chord were located at the hot spot location at an angle of 180 degrees to the CHS brace. The maximum SCFs of hybrid gapped tubular K-joints with circular braces and square chord were located generally at the hot spot location at an angle of 0 degrees to the CHS brace. Test results were compared against the design predictions in accordance with the current design guidelines of the International Committee for the Development and Study of Tubular Structures (CIDECT, 2001). Upon comparison, it was found that the design formulas of CIDECT (2001) overestimate the maximum SCFs of SHS-to-CHS hybrid gapped tubular K-joints. For the CHS chord and SHS braces of hybrid overlapped tubular K-joints, the design formulas overestimate the maximum SCFs for most of the specimens. Furthermore, for the SHS chord and CHS braces of hybrid gapped tubular K-joints, the design formulas of CIDECT (2001) overestimate the maximum SCFs. For the SHS chord and CHS braces of hybrid overlapped tubular K-joints, the CIDECT (2001) design formulas were unconservative when determining the maximum SCFs of such joints.

Stress Concentration Factors Of Tubular Kk-Joints Under Balanced Axial Loading

A Numerical Study and Proposed Design Rules for Stress Concentration Factors of Stainless Steel Hybrid Tubular K-joints

An Experimental Study on Stress Concentration Factors of Stainless Steel Hybrid Tubular K-joints

Prediction of Stress Concentration Factor Distribution for Multi-Planar Tubular DT-joints under Axial Loads

Experimental investigation of SCF distribution for thin-walled concrete-filled CHS joints under axial tension loading

EXPERIMENTAL RESEARCH AND FINITE ELEMENT ANALYSIS ON A WELDED JOINT WITH TUBES INTERSECTED AT TWO DIFFERENT POINTS

Empirical modeling of stress concentration factors using finite element analysis and artificial neural networks for the fatigue design of tubular KT‐joints under combined loading

Numerical Investigation and Design Rules for Stress Concentration Factors of Stainless-Steel Hybrid Tubular Joints

Experiment investigations of stress concentration factor of concrete-filled tubular T joints

Stress Concentration Factor Distribution Formulas for Three-Planar Tubular Y-joints under Axial Force

Experimental Evaluation of Stress Concentration Factor of Welded Steel Bridge T-Joints

Scf Distribution Of Concrete-Filled Chs T- And Y- Joints Under Axial Tension

A method for stress concentration factor determination of welded steel bridge T-joints under moving load

Study on stress concentration factor of concrete-filled steel tubular T-joints

Experimental Study of Hot Spot Stress for Three-Planar Tubular Y-joint: I. Basic Loads

Fatigue tests of multiplanar concrete-filled steel tubular KK-joints with inner ring stiffeners

Effect of welding residual stress on the performance of CFST tubular joints

Stress influence matrix on hot spot stress analysis for welded tubular joint in offshore jacket structure

Fatigue Analysis on a Multi-planer Tubular KK Joints Based on Scalded Model Test

Stress Concentration Factors of Brace In-Plane Loaded Bird-Beak SHS Gap K-joints

Numerical Study of Hybrid Tubular K-joints with Circular Braces and Square Chord in Stainless Steel