Abstract:Tungsten alloy has a wide range of applications in aerospace and defense industry because of its high hardness, high strength and other excellent properties. Tungsten alloys are typical hard-to-machine materials, and the electroplastic effect can improve the machining surface quality of hard-to-machine metal materials. However, the complex thermal–mechanical-electrical coupling generated by the relative motional squeezing of the tool and the workpiece under the electric pulse. It will cause a large difference between the physical and mechanical properties of the surface layer and the substrate material. The size and distribution of the characteristic parameters of the physical and mechanical properties of the machined surface, such as work hardening, residual stress and metamorphic layer, are not clear. Therefore, characterization of the physical and mechanical properties of the surface of W93NiFe alloy for electroplasticity-assisted dry turning machining was carried out in this paper. The results showed that the electrically plastic assisted dry turning process effectively alleviated the degree of work hardening on the machined surface of W93NiFe alloy. but the oxidation of the surface layer of the workpiece was exacerbated by excessive pulse voltage, which resulted in the increase of the surface microhardness again; Compared with conventional dry turning, the application of appropriate pulse voltage can effectively reduce the residual stress on the machined surface of W93NiFe alloy. and in this experiment, the variation of pulse frequency had less effect on the residual stress on the machined surface of W93NiFe alloy; After passing the pulse current, the thickness of the surface metamorphic layer increased significantly with the increase of electrical parameters such as pulse voltage and pulse frequency. but there was no significant effect of the two processing methods on the internal organization of W93NiFe alloy.

Cutting Mechanism of WC-8Co Cemented Carbide for Dry Turning of Ti6A14V Before and After Pulsed Electromagnetic Coupling Processing

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

Wear Mechanisms of Cemented Carbide Tools in Dry Cutting of Precipitation Hardening Semi-Austenitic Stainless Steels

Pulsed Magnetic Field Treatment of WC-TiC-Co Cutting Inserts for Improved Microstructure and Cutting Performance

Improving Wear Resistance and Corrosive Resistance of Cemented Carbide for Mud Pulser Rotor by Deep Cryogenic Treatment

Wear characteristics and micro-cutting damage model of cemented carbide by deep cryogenic treatment

Performance and wear mechanism of spark plasma sintered WC-Based ultrafine cemented carbides tools in dry turning of Ti–6Al–4V

Preparation, properties and microstructure of high hardness WC-co cemented carbide tool materials for ultra-precision machining

Influence of cutting parameters on PCD tool wear during milling tungsten carbide

Diffusion Wear in Dry Cutting of Ti–6Al–4V with WC/Co Carbide Tools

Characterization of Physical and Mechanical Properties of Tungsten Alloy Surfaces for Electroplasticity-Assisted Dry Cutting Machining

Cutting Performance and Failure Mechanisms of a Pure WC Cutting Tool in Dry Cutting of Cr12Mn5Ni4Mo3Al Stainless Steels and HT200 Grey Cast Iron

Performance improvement of carbide cutting tool for Ti6Al4V alloys using electromagnetic treatment

Experimental investigation on the problems in the achievement of super-smooth surface of cemented carbide WC-Co through diamond turning

Influence of Deep Cryogenic Treatment on Microstructures and Mechanical Properties of an Ultrafine-Grained WC-12Co Cemented Carbide

Multi-pattern failure modes and wear mechanisms of WC-Co tools in dry turning Ti–6Al–4V

Enhancement of carbide tool performance during dry machining through a combination of laser surface texturing and tungsten disulfide soft coatings

The Cutting Performance of Ultra-Smooth Composite Diamond Coated Wc-Co Inserts in Dry Turning Al/Sic-Mmc

Mechanism of material removal in tungsten carbide-cobalt alloy during chemistry enhanced shear thickening polishing

The Effect of Cryogenic Treatment on Microstructure and Properties of WC–Co Cemented Carbides

Friction and wear behaviors of the carbide tools embedded with solid lubricants in sliding wear tests and in dry cutting processes