Abstract:The dynamic stall of the airfoil can adversely affect the performance of helicopter rotor blades, jet engine compressor blades, wind turbine blades, and so on. Therefore, the flow control on the dynamic stall is necessary. This paper conducted an experimental study on the multiobjective flow control effect of the dynamic stall on a NACA0012 airfoil using a passive vortex generator (VG). The control effect of the VG on the dynamic stall is discussed, and the control mechanism is explained. Within the scope of this paper, the VG could significantly increase the maximum normal force coefficient (Cn) by 0.223, reduce the peak negative moment coefficient (Cm) by 0.049, and delay the stall angle of attack of Cn and Cm by & UDelta;& alpha;=1.8 & DEG; and 2.9 & DEG;, respectively. These multiobjective control effects were attributed to the control of the complex vortices on the suction surface. The VG delays stall by suppressing the formation of the shear layer vortex, and enhances the aerodynamic performance during dynamic stall by energizing the dynamic stall vortex (DSV). The effects of the VG on the convection speed and strength of the DSV are additionally investigated from a space-time perspective. Within the reduced-frequency range studied in this paper, the DSV convection speed controlled by VG was smaller than that of the baseline airfoil, and the VG could significantly enhance the strength of the DSV. Dynamic stall phenomena are widely found in nature (wings of flying birds, fins of swimming fish, and so on) and in engineering (bionic flutter wings, helicopter rotors, wind turbine blades, and so on). It is widely believed that the DSV is the main flow structure dominating the dynamic stall. For helicopter rotor blades and large wind turbine blades, dynamic stall is prone to occur in the blade tip under complex realistic conditions. The vortex lift during dynamic stall will significantly raise the blade load, and the motion of the DSV will cause a sharp change in the blade moment, which may damage the blade structure and control system. Therefore, the dynamic stall needs to be controlled. In this paper, passive VGs were used to control the dynamic stall on an airfoil, and ideal multiobjective control effects were obtained: reducing the negative peak moment, increasing the maximum lift coefficient, delaying the stall, and reducing the hysteresis effect. This work is a guideline for the dynamic stall control of helicopter rotor and wind turbine blades.

Numerical Investigation On Effect Of Compressor Performance In Single Rotor With Micro-Vortex Generator

Experimental investigation of transient characteristics of mild surge and diffuser rotating stall in a centrifugal compressor with vaned diffuser

Vortex Generator Evaluation Models and Flow Mechanisms for Compressor Cascade

Effects of Vortex-Vortex Interaction in A Compressor Cascade with Vortex Generators

Efficient Optimization Design of Vortex Generators in a Highly Loaded Compressor Stator

Investigation of Helicopter Rotor Aerodynamic Characteristics in Axial Descent with Viscous Vortex Particle Method

Numerical Investigation of Transient Flow Characteristics in a Centrifugal Compressor Stage with Variable Inlet Guide Vanes at Low Mass Flow Rates

An Experimental Investigation On The Clocking Effect Between Inlet Guide Vanes And Vaned Diffuser In A Centrifugal Compressor Stage

Experimental and Numerical Analysis of Unsteady Flow Structure in a Centrifugal Compressor with Variable Vaned Diffuser

Research on Stall Mechanism Based on Vorticity Dynamics in a Single-Rotor Axial Compressor

Efficient Design Method for Applying Vortex Generators in Turbomachinery

Effect of Variable Stator Vanes with Penny Cavities on the Performance and Secondary Flow of a Single-Stage Axial Compressor

Theory and analysis method based on vorticity dynamics for gas turbine compressor

NUMERICAL INVESTIGATION OF A CENTRIFUGAL COMPRESSOR WITH A SINGLE CIRCUMFERENTIAL GROOVE IN DIFFERENT TYPES OF DIFFUSERS

Some Effects of Non-Axisymmetric Tip Clearance Layout on Axial Compressor Aerodynamics

Influence of Sub Boundary Layer Vortex Generator Height and Attack Angle on Cross-Flows in the Hub Region of Compressors

NUMERICAL INVESTIGATION OF DIFFUSER FLOW FIELD AND ROTATING STALL IN A CENTRIFUGAL COMPRESSOR WITH VANED DIFFUSER

Numerical investigation of thermo-hydraulic performance of perforated rectangular and sinusoidal vortex generators in a double-pipe heat exchanger

Numerical Investigation of a Variable Stator Vane with Nonuniform Partial Radial Gaps in an Annular Compressor Cascade

Experimental Study on Multiobjective Flow Control of Dynamic Stalls Using a Vortex Generator

Study on the influence of variable inlet guide vane slot on the aerodynamic performance in air storage centrifugal compressor