Abstract:Abstract With increasing aerodynamic and thermal loads, film cooling has been a popular technology integrated into the design of the modern gas turbine vane endwall, especially for the first-stage vane endwall. A staggering amount of research has been completed to quantify the effect of operating conditions and cooling hole geometrical properties. However, most of these investigations did not address the influence of the manufacturing tolerances, assembly errors, and operation degradations on the endwall misalignment. In this paper, uncertainty quantification (UQ) analysis was performed to quantify the impacts of upstream endwall misalignment uncertainties on the endwall film cooling performance and vane surface phantom cooling performance. The upstream endwall misalignment, step geometry with various step heights, commonly exists between the combustor exit and the first-stage vane endwall. Based on the non-intrusive polynomial chaos expansion (NIPC) and the uniform probability distribution assumption, the deviation (step height) uncertainties of the upstream endwall misalignment were quantified. To predict the endwall secondary flow and film cooling effectiveness in the transonic linear vane passage, the commercial computational fluid dynamic solver ANSYS FLUENT was used to numerically solve the three-dimensional steady-state Reynolds-Averaged Navier–Stokes (RANS) equations. The robustness analysis of endwall film cooling performance and phantom cooling performance to the upstream endwall misalignment was conducted for three design upstream step heights (ΔH): a baseline configuration (ΔH = 0 mm), two misaligned configurations with forward step (ΔH = −5 mm) and backward step (ΔH = 5 mm), respectively. Results show that the actual cooling performance has a high probability of deviating from the nominal value for the baseline configuration. The critical regions that are most sensitive to the upstream step misalignment are also identified by variances. The UQ results also show that the design geometry with a forward step has a more robust film cooling performance on endwall and phantom cooling performance on the vane pressure side surface, which means a smaller variance and a better expectation than the no-step configuration. In contrast, the design geometry with a backward step induces the reductions in the expectation of the film cooling effectiveness and coolant coverage and the amplification of performance fluctuations. This work provides a certain guiding direction for the optimization design for the upstream step geometry.

Numerical Investigation and Optimization of Variable Guide Vanes Adjustment in a Transonic Compressor

Experimental Investigation to Combination of Simultaneous Adjustment to Inlet Guide Vanes and Diffuser

Optimization of Three-Dimensional Blade and Variable Stators for Efficiency and Stability Enhancement of Multistage Axial Flow Compressor at Variable Speeds

Numerical Investigation of a Variable Stator Vane with Nonuniform Partial Radial Gaps in an Annular Compressor Cascade

Optimization Design of Aspect Ratio and Solidity of a Heavy-Duty Gas Turbine Transonic Compressor Rotor

Aerodynamic Optimization and Mechanism Investigation on Performance Improvements in a Transonic Compressor Cascade

Design of A Single-Stage Centrifugal Compressor and Numerical Investigation of Simultaneous Adjustment of Inlet Guide Vanes and Diffuser Vanes

Numerical Investigation of Wall Heating/Cooling Effect on the Transonic Compressor Performance

INFLUENCE OF ADJUSTABLE INLET GUIDE VANES ON THE PERFORMANCE CHARACTERISTICS OF A SHROUDED CENTRIFUGAL COMPRESSOR

Numerical investigation of the influence of suction surface synthetic jet on the performance of transonic axial flow compressor

An Experimental Investigation On The Clocking Effect Between Inlet Guide Vanes And Vaned Diffuser In A Centrifugal Compressor Stage

NUMERICAL INVESTIGATION OF UNSTEADY SHOCK WAVE MOTION IN A TRANSONIC CENTRIFUGAL COMPRESSOR

Uncertainty Quantification on the Cooling Performance of a Transonic Turbine Vane With Upstream Endwall Misalignment

Numerical Investigation of Unsteady IGV-Impeller-Diffuser Interaction in a Centrifugal Compressor

Numerical Investigation on the flow in a stage of Transonic Centrifugal Compressor with Vaned Diffuser Coupling with Different Configuration of Volute

Experiment Investigation on Secondary Flow Loss and Flow Control Mechanisms in a Variable Compressor Cascade with Penny Cavities

Experimental Study on the Aerodynamic Performance of Variable Geometry Low-Pressure Turbine Adjustable Guide Vanes

Stator re-stagger optimization in multistage axial compressor

Numerical Simulation on Unsteady Flow Mechanism of a 1.5-Stage Axial Transonic Compressor

A numerical study of multistage axial compressor stability

An improved deviation model for transonic stages in axial compressors