Abstract:Thin solid films have many applications in a wide range of industries, and consequently are important materials. For structural applications, it is essential to understand the mechanical properties of thin films so that the performance and reliability of thin-film based devices can be optimised. Accurate measurement of the mechanical properties of thin films presents a challenge, as the films are often too thin to allow them to be handled alone and hence they are usually attached to a substrate. A study of the literature demonstrates that significant research effort has been directed towards developing appropriate testing methodologies for mechanical characterisation of thin films in the past two or three decades; however, the existing methods do have limitations due to difficulties in specimen preparation and manipulation, and the lack of unified testing standards. Furthermore, the accuracy obtained in measuring a given mechanical property is often affected by the complex nature of the thin film structure, or the microstructure of the material itself. There is, therefore, a requirement for ongoing effort to develop mechanical characterisation methods that are accurate and cost-effective, especially for ultra-thin films on the nanometric scale. Dynamic testing has been one of the popular approaches used to measure the mechanical properties of thin films. Using the resonant vibration behaviour of a thin-film structure, the material and mechanical properties of the film can be obtained. The technique displays great potential for the mechanical characterisation of thin films, as the sample preparation is relatively simple and the measurement can be self-calibrated. This work aims to systematically investigate the dynamic behaviour of two thin-film structures, including cantilever beams and circular diaphragms, and thus develop novel dynamic testing methodologies for measuring the elastic modulus, density and residual stress of ultra-thin films. A membrane-based resonant method for measuring the tensile residual stress of a circular thin-film diaphragm was developed. In this method, the frequency ratio of the first two symmetric vibration modes was proposed as a criterion based on the RayleighnRitz method. The method was validated using suspended silicon carbide membranes experimentally and numerically, and the tensile stresses measured were in reasonably good agreement with those obtained from the wafer curvature measurement. This approach measures residual stress directly, and does not require any knowledge of film thickness; it can also be extended to any thin solid film with a suspended membrane structure. A novel resonant method was also developed to simultaneously determine the residual stress and elastic modulus of a suspended circular thin-film diaphragm that exhibits a combination of plate and membrane behaviour. The mechanical properties were determined by solving the RayleighnRitz equation theoretically using the experimentally measured resonant frequencies of the first two symmetric vibration modes of the diaphragm. The experimental results were found to be in excellent agreement with the finite element modelling. The modulus and stress values were also in reasonably good agreement with those obtained from the nanoindentation and the wafer curvature measurements, respectively. The limitations of the diaphragm and membrane methods, and the effects of sample preparation and testing environment on measuring accuracy, have also been comprehensively addressed. A simple and practical method was also proposed to simultaneously characterise both the mass density and elastic modulus of a thin film using Euler-Bernoulli beam theory with the measured resonant frequencies of bare and two composite cantilever beams. The method was validated using a sputter-coated Ni film/Si substrate system. The elastic modulus of the Ni film obtained from this method was in excellent agreement with that measured using nanoindentation. This method is of special importance for characterising thin films of porous materials, as the measurement is non-contact and the calculation is only slightly influenced by viscous damping.

A Micro-Vibration Apparatus for Dynamic Mechanical Analysis of Ultrathin Polymer Films.

Novel technique for mechanical characterization of thin polymeric tissue membrane

A Novel Technique for Mechanical Characterization of Thin Elastomeric Membrane

Dynamic Characterisation of Mechanical Properties of Ultrathin Films

Soft Three-Dimensional Microscale Vibratory Platforms for Characterization of Nano-Thin Polymer Films

A Systematic Method for Characterizing the Elastic Properties and Adhesion of a Thin Polymer Membrane

Nanoscale rheology: Dynamic Mechanical Analysis over a broad and continuous frequency range using Photothermal Actuation Atomic Force Microscopy

Development of an experimental technique for testing rheological properties of ultrathin polymer films used in nanoimprint lithography

Nanoconfinement Controls Mechanical Properties of Elastomeric Thin Films

A New Micro-Tensile System for Measuring the Mechanical Properties of Low-Dimensional Materials - Fibers and Films

An Apparatus for Measuring Mechanical Properties of Microstructures in Tensile Mode

In Situ and Real-Time Tensile Testing of Thin Films Using Double-Field-of-view Electronic Speckle Pattern Interferometry

OS5-2-3 an In-Situ Micro-Tension Setup and Its Application

Simultaneous Determination of the Residual Stress, Elastic Modulus, Density and Thickness of Ultrathin Film Utilizing Vibrating Doubly Clamped Micro-/Nanobeams

Elastic Property Characterization of Soft Substrate-Supported Thin Films Using Multiscale Digital Image Correlation

Identification and design of novel polymer-based mechanical transducers: A nano-structural model for thin film indentation

Non-destructive mapping of stress and strain in soft thin films through sound waves

Investigation on dynamic rheology properties of ultra-thin film using ultra-vacuum non-contact AFM

New Internal Stress Driven on-Chip Micromachines for Extracting Mechanical Properties of Thin Films

A New Method for the Micro-Tensile Testing of Thin Film

Micro-mechanical Characterisation for MEMS Thin Films by Bending Μ-Machined Cantilevers