Abstract:Thin solid films have many applications in a wide range of industries, and consequently are important materials. For structural applications, it is essential to understand the mechanical properties of thin films so that the performance and reliability of thin-film based devices can be optimised. Accurate measurement of the mechanical properties of thin films presents a challenge, as the films are often too thin to allow them to be handled alone and hence they are usually attached to a substrate. A study of the literature demonstrates that significant research effort has been directed towards developing appropriate testing methodologies for mechanical characterisation of thin films in the past two or three decades; however, the existing methods do have limitations due to difficulties in specimen preparation and manipulation, and the lack of unified testing standards. Furthermore, the accuracy obtained in measuring a given mechanical property is often affected by the complex nature of the thin film structure, or the microstructure of the material itself. There is, therefore, a requirement for ongoing effort to develop mechanical characterisation methods that are accurate and cost-effective, especially for ultra-thin films on the nanometric scale. Dynamic testing has been one of the popular approaches used to measure the mechanical properties of thin films. Using the resonant vibration behaviour of a thin-film structure, the material and mechanical properties of the film can be obtained. The technique displays great potential for the mechanical characterisation of thin films, as the sample preparation is relatively simple and the measurement can be self-calibrated. This work aims to systematically investigate the dynamic behaviour of two thin-film structures, including cantilever beams and circular diaphragms, and thus develop novel dynamic testing methodologies for measuring the elastic modulus, density and residual stress of ultra-thin films. A membrane-based resonant method for measuring the tensile residual stress of a circular thin-film diaphragm was developed. In this method, the frequency ratio of the first two symmetric vibration modes was proposed as a criterion based on the RayleighnRitz method. The method was validated using suspended silicon carbide membranes experimentally and numerically, and the tensile stresses measured were in reasonably good agreement with those obtained from the wafer curvature measurement. This approach measures residual stress directly, and does not require any knowledge of film thickness; it can also be extended to any thin solid film with a suspended membrane structure. A novel resonant method was also developed to simultaneously determine the residual stress and elastic modulus of a suspended circular thin-film diaphragm that exhibits a combination of plate and membrane behaviour. The mechanical properties were determined by solving the RayleighnRitz equation theoretically using the experimentally measured resonant frequencies of the first two symmetric vibration modes of the diaphragm. The experimental results were found to be in excellent agreement with the finite element modelling. The modulus and stress values were also in reasonably good agreement with those obtained from the nanoindentation and the wafer curvature measurements, respectively. The limitations of the diaphragm and membrane methods, and the effects of sample preparation and testing environment on measuring accuracy, have also been comprehensively addressed. A simple and practical method was also proposed to simultaneously characterise both the mass density and elastic modulus of a thin film using Euler-Bernoulli beam theory with the measured resonant frequencies of bare and two composite cantilever beams. The method was validated using a sputter-coated Ni film/Si substrate system. The elastic modulus of the Ni film obtained from this method was in excellent agreement with that measured using nanoindentation. This method is of special importance for characterising thin films of porous materials, as the measurement is non-contact and the calculation is only slightly influenced by viscous damping.

Investigation on dynamic rheology properties of ultra-thin film using ultra-vacuum non-contact AFM

Direct Measurement of Plowing Friction and Wear of a Polymer Thin Film Using the Atomic Force Microscope

Atomic Force Microscopy of Transfer Film Development

Computational Studies of Nano-Mechanics of Ultrathin Perfluoropolyether Films

Investigation of Normal Dynamic Contact Stiffness and Damping Characteristics in Mixed Lubrication for Non-Gaussian Rough Surfaces

Surface Force Apparatus and Thin Film Rheology for Additive-Treated Lubricant

On modeling and measuring viscoelasticity with dynamic Atomic Force Microscopy

Surface Viscoelasticity Studies of Ultrathin Polymer Films Using Atomic Force Microscopic Adhesion Measurements

A Micro-Vibration Apparatus for Dynamic Mechanical Analysis of Ultrathin Polymer Films.

Investigation on microtribological behavior of thin films using friction force microscopy

Dynamic Study of Polymer Films by Friction Force Microscopy with Continuously Varying Load

Ultra-thin Film Friction Micro-Mechanism

The Co-Design of Interface Sensing and Tailoring of Ultra-Thin Film with Ultrasonic Vibration-Assisted Afm System

A Dynamic Rheological Model for Thin-Film Lubrication

Dynamic friction energy dissipation and enhanced contrast in high frequency bimodal atomic force microscopy

Method to measure the viscoelastic properties of nanometer entangled polymer films

Contact Stiffness and Damping of Liquid Films in Dynamic Atomic Force Microscopy

Topography and Friction Properties of Macromolecular Thin Films Using Atomic-Force-microscopy Technology

Investigation of Dynamic Viscoelastic Asymmetric Response of PA6 Film Based on Fractional Rheological Model

Nanoscale rheology: Dynamic Mechanical Analysis over a broad and continuous frequency range using Photothermal Actuation Atomic Force Microscopy

Dynamic Characterisation of Mechanical Properties of Ultrathin Films