Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Friction-induced Surface Textures of Liquid Crystalline Polymer Evaluated by Atomic Force Microscopy, Spectroscopy and Nanoindentation

Friction-induced Lubricating Nanocoatings of Main-Chain Thermotropic Liquid Crystalline Polymer

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Tribological Enhancement Effect of Main-Chain Thermotropic Liquid Crystalline Polymer

Direct Measurement of Plowing Friction and Wear of a Polymer Thin Film Using the Atomic Force Microscope

Toward Low Friction in High Vacuum by Designing Textured A-C/il Duplex Lubricating Film

Insights into friction behavior of textured amorphous carbon and lubricant composite system: Dependence on the lubricant viscosity and textured shape

Friction Anisotropy Induced by Oriented Liquid Crystal Molecules

Friction and Wear Protection Performance of Synthetic Siloxane Lubricants

Atomic-Scale Understanding on the Tribological Behavior of Amorphous Carbon Films under Different Contact Pressures and Surface Textured Shapes

Self-Lubrication Mechanism of Surface-Textured Polymer-Matrix Composites under the Induction of Frictional Stress

Preliminary study of the superlubricity behavior of ZrO2/PI lubricating with liquid crystal

Unraveling Tribochemistry and Self-Lubrication Mechanism of Polytetrafluoroethylene by Reactive Coarse-Grained Molecular Dynamics Simulations.

Friction‐induced Electroactive Β Polymorph of Poly(vinylidene Fluoride)

Friction dependence on the textured structure of an amorphous carbon surface: A reactive molecular dynamics study

Effects of Laser Surface Texturing and Lubrication on the Vibrational and Tribological Performance of Sliding Contact

Research on the antifriction mechanism of liquid crystal additives (LCA)

AFM Study on Superlubricity Between Ti6Al4V/Polymer Surfaces Achieved with Liposomes.

Nano-tribological Properties and Mechanisms of the Liquid Crystal As an Additive

Temperature-controlled Friction Coefficient Lubricated by Liquid Crystal

Effect of Liquid Crystal Molecular Orientation Controlled by an Electric Field on Friction