Abstract:Thin solid films have many applications in a wide range of industries, and consequently are important materials. For structural applications, it is essential to understand the mechanical properties of thin films so that the performance and reliability of thin-film based devices can be optimised. Accurate measurement of the mechanical properties of thin films presents a challenge, as the films are often too thin to allow them to be handled alone and hence they are usually attached to a substrate. A study of the literature demonstrates that significant research effort has been directed towards developing appropriate testing methodologies for mechanical characterisation of thin films in the past two or three decades; however, the existing methods do have limitations due to difficulties in specimen preparation and manipulation, and the lack of unified testing standards. Furthermore, the accuracy obtained in measuring a given mechanical property is often affected by the complex nature of the thin film structure, or the microstructure of the material itself. There is, therefore, a requirement for ongoing effort to develop mechanical characterisation methods that are accurate and cost-effective, especially for ultra-thin films on the nanometric scale. Dynamic testing has been one of the popular approaches used to measure the mechanical properties of thin films. Using the resonant vibration behaviour of a thin-film structure, the material and mechanical properties of the film can be obtained. The technique displays great potential for the mechanical characterisation of thin films, as the sample preparation is relatively simple and the measurement can be self-calibrated. This work aims to systematically investigate the dynamic behaviour of two thin-film structures, including cantilever beams and circular diaphragms, and thus develop novel dynamic testing methodologies for measuring the elastic modulus, density and residual stress of ultra-thin films. A membrane-based resonant method for measuring the tensile residual stress of a circular thin-film diaphragm was developed. In this method, the frequency ratio of the first two symmetric vibration modes was proposed as a criterion based on the RayleighnRitz method. The method was validated using suspended silicon carbide membranes experimentally and numerically, and the tensile stresses measured were in reasonably good agreement with those obtained from the wafer curvature measurement. This approach measures residual stress directly, and does not require any knowledge of film thickness; it can also be extended to any thin solid film with a suspended membrane structure. A novel resonant method was also developed to simultaneously determine the residual stress and elastic modulus of a suspended circular thin-film diaphragm that exhibits a combination of plate and membrane behaviour. The mechanical properties were determined by solving the RayleighnRitz equation theoretically using the experimentally measured resonant frequencies of the first two symmetric vibration modes of the diaphragm. The experimental results were found to be in excellent agreement with the finite element modelling. The modulus and stress values were also in reasonably good agreement with those obtained from the nanoindentation and the wafer curvature measurements, respectively. The limitations of the diaphragm and membrane methods, and the effects of sample preparation and testing environment on measuring accuracy, have also been comprehensively addressed. A simple and practical method was also proposed to simultaneously characterise both the mass density and elastic modulus of a thin film using Euler-Bernoulli beam theory with the measured resonant frequencies of bare and two composite cantilever beams. The method was validated using a sputter-coated Ni film/Si substrate system. The elastic modulus of the Ni film obtained from this method was in excellent agreement with that measured using nanoindentation. This method is of special importance for characterising thin films of porous materials, as the measurement is non-contact and the calculation is only slightly influenced by viscous damping.

Elastic Property Characterization of Soft Substrate-Supported Thin Films Using Multiscale Digital Image Correlation

Study of Elastic Modulus and Yield Strength of Polymer Thin Films Using Atomic Force Microscopy

Study on Young'S Modulus of Thin Films on Kapton by Microtensile Testing Combined with Dual Dic System

Finite Deformation Mechanics In Buckled Thin Films On Compliant Supports

Measuring elastoplastic properties of thin films on an elastic substrate using sharp indentation

“Contact” of Nanoscale Stiff Films

Study on the Effect of DIC Deformation Sensor on Mechanical Property of Substrate

In Situ and Real-Time Tensile Testing of Thin Films Using Double-Field-of-view Electronic Speckle Pattern Interferometry

SMART Transfer Method to Directly Compare the Mechanical Response of Water-Supported and Free-Standing Ultrathin Polymeric Films.

Deformation Mechanisms of Polymer Thin Films by Simultaneous Kinetic Measurement of Microscopic Infrared Dichroism and Macroscopic Stress. Part Iii: Influence of Morphology on Molecular Orientation of Isotactic Polypropylene Films Subjected to Uniaxial Stretching

Novel technique for mechanical characterization of thin polymeric tissue membrane

Strain Transfer Through Film-Substrate Interface and Surface Curvature Evolution During a Tensile Test

A Measuring System for Mechanical Characterization of Thin Films Based on a Compactin Situmicro-Tensile Tester and SEM Moiré Method

90-degree peeling of elastic thin films from elastic soft substrates: Theoretical solutions and experimental verification

Non-destructive mapping of stress, strain and stiffness of thin elastically deformed materials

The application of digital image techniques to determine the large stress–strain behaviors of soft materials

Droplet Spreading Induced Wrinkling and Its Use for Measuring the Elastic Modulus of Polymeric Thin Films

"Contact" of nanoscale stiff films.

Dynamic Characterisation of Mechanical Properties of Ultrathin Films

Imaging Interface Stress and Strain in Heterogeneous Films

Water‐assisted Mechanical Testing of Polymeric Thin‐films