Abstract:Si3N4/SiC composites containing 0-30 vol% SiC were fabricated by pressureless sintering and sinter-post-HIPing method using fine Si3N4 and nano-sized SiC powders. Specimens reached full density (>96% theoretical density (th. d.)) except the composites made by pressureless sintering which contained a small amount of sintering additives or a large amount of SiC. All composites with 10 mass% sintering additives reached full density (similar to 99% th. d.) by sinter-post-HIPing. The addition of SiC particles greatly influenced the grain morphology of the Si3N4 matrix. The average grain thickness, length and aspect ratio decreased with increasing SiC content because of grain boundary pinning by SiC particles. Also the mechanical properties were markedly dependent upon the fraction of SiC particle reinforcement, as well as matrix grain size and porosity. When the materials were pressureless sintered, the strength of the composite increased with SiC additions below 20 vol%. Further increase in the SIC content resulted in a corresponding decrease in strength. Maximum strength of 1150 MPa was attained at 20 vol% SiC addition. The increase in strength by addition of SiC is due to decrease of grain size of Si3N4 matrix grain size, and the decrease by further increase in SiC content is caused by porosity and SiC agglomerate. On the other hand, toughness decreased monotonically with SiC content. The strength of all samples was enhanced by sinter-post-HIPing without any change in fracture toughness. The strength of sintered samples with 10-15 vol% SiC increased by similar to 20% to 1260 MPa by post-HIPing. The increase in strength by post-HIPing was interpreted as being due to a decrease flaw size.

In Situ Formation of SiC in Al–40Si Alloy During High-Pressure Solidification

Microstructural Evolution and Mechanical Properties of SiC/Al-40Si Composites Fabricated by High Pressure Solidification.

Nano-Phase and SiC–Si Spherical Microstructure in SiC/Al-50Si Composites Solidified under High Pressure

Microstructure Evolution and Precipitation of SiC Particle Reinforced Al–20Si Composite Solidified under High Pressures

Interconnected SiC–Si Network Reinforced Al–20Si Composites Fabricated by High Pressure Solidification

The Thermal Expansion Behaviour of SiCp/Al–20Si Composites Solidified under High Pressures

Interfacial Regulation and Fracture Mechanism of Al–Si/SiC Composites Infiltrated under Super-Gravity Field

In Situ Al Based Composites Fabricated in Al-SiO2-C System by Reaction Sintering

Effects of high pressure and SiC content on microstructure and precipitation kinetics of Al-20Si alloy

Study of SiC/Al nanocomposites under high pressure

Effect of Pressure on the Solidification Behavior and Mechanical Properties of SiCp/Al-Mg Composites

In-situ synthesis of nano SiC particles in Al–Si–C system at 750 °C

Fabrication and Mechanical Properties of Si3N4/SiC Nanocompoisites under Pressureless Sintering.

The study of pressureless-sintered Mo(Si,Al)(2)-SiC composite

Pressureless Infiltration Preparation of High SiC/Al Ceramic Matrix Composites

Fabrication, Microstructure, and Properties of SiC/Al 4 SiC 4 Multiphase Ceramics Via an In-Situ Formed Liquid Phase Sintering

Interfacial microstructure of SiCp/Al composite produced by the pressureless infiltration technique

Effects of SiC contents on the microstructure and mechanical properties of Al4SiC4–SiC ceramic composites

Microstructure, Mechanical, and Thermal Properties of in Situ-Synthesized (zrb2+sic)/zr2[al(si)]4c5 Composites

Microstructure and Hardness Performance of a SiCp/Al Composite by Pressureless Infiltration Technique

Fabrication and Mechanical Properties of Si3n4/Sic Nanocomposite with Pressureless Sintering and Sinter-Post-Hiping