Abstract:To meet the practical application, a kind of commercially available Si3N4 powder by direct Si nitridation was used to fabricate dense Si3N4/SiC nanocomposite by pressureless sintering method. The price of this kind of powder is much lower than that of powder by imide decomposition. 5-30 vol% of SiC powder (average particle size: 80 nm) were added in the composite to investigate the effect of SiC particle. Totally 15 wt% of MgAl2O4 and ZrO2 (50 wt% each) were used as sihtering additives. With increasing SiC content, the densities of the composites decreased. α-β Si3N4 phase transformation was enhanced at low temperatures, but prohibited at high temperatures for large SiC content. The sample with larger SiC content gave a relatively smaller Si3N4 grain size because SiC particles limit the Si3N4 grain growth by pinning and prohibiting the grain boundary movement. An improvement of Young's modulus, flexural strength and hardness by the SiC addition was found. Further increase in SiC content resulted in a decrease of these properties because of the decreasing density for the samples sintered at low temperatures. With an intermediate sintering temperature, the samples with 20 vol% SiC reached to high flexural strength as 1050 MPa as a result of good density and relatively fine grain size structure. The decreased fracture toughness with increasing the SiC content was observed by the refinement of Si3N4 grain. However, it was improved with the increasing sintering temperature. The result of this study provided an economic way to fabricate the Si3N4/SiC nanocomposite with a strength higher than 1 GPa and appropriate fracture toughness.

Interconnected SiC–Si Network Reinforced Al–20Si Composites Fabricated by High Pressure Solidification

Microstructural Evolution and Mechanical Properties of SiC/Al-40Si Composites Fabricated by High Pressure Solidification.

Effect of Particle Strength on SiCp/Al Composite Properties with Network Architecture Design

Study of SiC/Al nanocomposites under high pressure

Fracture Behaviour of SiCp/Al Composites with Network Architecture

Nano-Phase and SiC–Si Spherical Microstructure in SiC/Al-50Si Composites Solidified under High Pressure

Interfacial Regulation and Fracture Mechanism of Al–Si/SiC Composites Infiltrated under Super-Gravity Field

Effect of Pressure on the Solidification Behavior and Mechanical Properties of SiCp/Al-Mg Composites

Microstructure Evolution and Precipitation of SiC Particle Reinforced Al–20Si Composite Solidified under High Pressures

In Situ Formation of SiC in Al–40Si Alloy During High-Pressure Solidification

The Thermal Expansion Behaviour of SiCp/Al–20Si Composites Solidified under High Pressures

Effects of high pressure and SiC content on microstructure and precipitation kinetics of Al-20Si alloy

Microstructures and enhanced mechanical properties of (Al3Ti+Al2O3)/Al–Si composites with co-continuous network structure prepared by pressure infiltration

Strengthening Behavior in SiC Nanowires Reinforced Pure Al Composite

Mechanical Behavior and Interfacial Micro-Zones of SiCp(CNT) Hybrid Reinforced Aluminum Matrix Composites

High Content SiC Nanowires Reinforced Al Composite with High Strength and Plasticity

Strengthening and Fracture Behaviors in SiCp/Al Composites with Network Particle Distribution Architecture

Fabrication of 3D-SiC network reinforced aluminum–matrix composites by pressureless infiltration

Microstructure and Properties of Hot Pressed Zr2(Al(Si))4C5/SiC Composites

Microstructure and Mechanical Properties of 45 vol.% SiC p /7075Al Composite

Fabrication and Mechanical Properties of Si3N4/SiC Nanocompoisites under Pressureless Sintering.