Abstract:Welding residual stress (WRS) significantly influences the fatigue life and safety of welded steel structures. Post-weld heat treatment (PWHT) is a common method employed to mitigate WRS. In present study, the WRS evolution law and relaxation mechanism of U-rib-to-deck joints was investigated during PWHT. High-temperature heat treatment tests with varying holding times were conducted on U-rib-to-deck joints to reduce WRS. The WRS distributions were measured using the hole-drilling method before and after PWHT. ABAQUS software, incorporating the Norton-Bailey creep constitutive model, was employed to simulate the WRS evaluation during both welding and PWHT processes. The simulated values were validated against the measured data, and the effects of different holding times, holding temperatures, and heating and cooling rates during PWHT on WRS relaxation were discussed. The results demonstrate that PWHT effectively reduces WRS and leads to a more uniform distribution. Extending the PWHT holding time from 0.5 h to 1 h and 2 h results in a gradual decrease in WRS relaxation at 600 °C, primarily occurring in the high-value stress region of the weld zone with a small amplitude. Elevating the PWHT temperature from 500 °C to 550 °C and subsequently to 600 °C amplifies the significance of WRS relaxation. Variations in heating and cooling rates (200 °C/h and 80 °C/h, 100 °C/h and 40 °C/h, 50 °C/h and 20 °C/h) lead to a gradual decrease in WRS relaxation across the entire model. Furthermore, considering the creep effect, the stress relaxation rate in the weld is approximately 70 %–80 %, which found to be about 2–3 times higher than that without considering the creep effect. By understanding the evolution law and relaxation mechanism, this study provides valuable insights for designing PWHT processes and assessing their impact on structural safety and fatigue life.

A Primary Plus Secondary Local PWHT Method for Mitigating Weld Residual Stresses in Pressure Vessels

The primary-auxiliary local post-welding heat treatment method to control welding residual stresses for pressure vessels

A rigid-flexible coordinated method to control weld residual stress and deformation during local PWHT for ultra-large pressure vessels

Local Post Weld Heat Treatment of a Pressure Vessel: A Postmortem Evaluation

Effect of Post-Weld Heat Treatment on the Plastic Buckling of Welded Cylindrical Shells

Prediction of Residual Stress Distributions in Welded Sections of P92 Pipes with Small Diameter and Thick Wall Based on 3D Finite Element Simulation

Using reinforce plate to control the residual stresses and deformation during local post-welding heat treatment for ultra-large pressure vessels

INVESTIGATION ON TWO ASSESSING CRITERIA IN LOCAL POSTWELD HEAT TREATMENT

Post-Weld Heat Treatment of API 5L X70 High Strength Low Alloy Steel Welds

Numerical and experimental investigations on the temperature field in local post weld heat treatment of 9 % Cr heat resistant steel welded pipes

On Residual Stress and Relief for an Ultra-Thick Cylinder Weld Joint Based on Mixed Hardening Model: Numerical and Experimental Studies

A study on the mechanical stress relieving and safety assessment without post-weld heat treatment

Residual stresses evolution during strip clad welding, post welding heat treatment and repair welding for a large pressure vessel

Effect of Local Rapid Cooling Heat Treatment on Residual Stress of Pressure Vessel Inner Wall Welding Layer

Effect of Residual Stress Distribution in Multi-Pass Welding on Stress Relief Criterion in Local Post Weld Heat Treatment of Pipe

Evolution of Residual Stresses in Dissimilar Steel Surfacing Layers During Process of Post-Weld Heat Treatment

Influence of post-weld heat treatment on welding residual stress in U-rib-to-deck joint

Heated band width criterion in local post weld heat treatment of three dimensional tubular joint

Heated Band Width Criterion Based on Stress Relief in Local Post Weld Heat Treatment of Concurrent Tubular Joint

Assessing Toughness Levels for Nuclear Containment Vessels Steel to Determine the Need for Postweld Heat Treatment Based on the Master Curve Method

Numerical Studies of Post Weld Heat Treatment on Residual Stresses in Welded Impeller