Abstract:This investigation examines the correlation between room temperature tensile properties and the fractal dimension of fracture surfaces in modified 9Cr-1Mo steel, using heat-treated Group-I and Group-II specimens. Group-I specimens with bainitic morphology were austenitized at 1000 °C and isothermally held at 460 °C, then divided into Set-I (water quenched) and Set-II (air-cooled). Group-II specimens were austenitized at 1000 °C, austempered at 460 °C and 480 °C for 6 hours, and water quenched, forming Set-III and Set-IV, respectively. All Group-II specimens were tempered at 760 °C for varying durations and air-cooled. Results indicate that the fractal dimension of Set-I specimens in Group-I positively correlates with Vickers hardness, while Set-II shows a negative correlation. In Group-II, no linear relationship was observed between fractal dimension and hardness. The fractal dimension of Group-I did not change with tensile strength. For elongation, Set-I specimens in Group-I showed no variation except at 60 min of isothermal holding, whereas Set-II's fractal dimension increased with elongation. In Group-II, Set-III's fractal dimension increased with tempering and decreased without tempering. The fractal dimension of Set-IV specimens fluctuated with tempering duration and then increased with tensile strength. Regarding toughness, Set-I specimens in Group-I showed no variation except at 60 min of isothermal holding. Set-IV specimens in Group-II had a negative correlation with toughness. Set-III's fractal dimension decreased with tensile toughness, while Set-IV's increased weakly. The fractal dimension of Set-III specimens in Group-II could estimate tensile fracture toughness. This study highlights complex relationships between fractal dimensions and mechanical properties in modified 9Cr-1Mo steel, influenced by heat treatment conditions.

An Investigation of the Effects of Grain Size and Hardness in Temper-Embrittled 2 1/4 Cr-1 Mo Steel

Mesoscopic mechanical properties of 18Cr-8Ni austenitic steel subjected to low-cycle fatigue loading

Investigation of fatigue mesoscopic mechanical properties of a nickel-based superalloy by instrumented microindentation measurements

Effect of Different Water Toughening Treatment on Mechanical Properties and Microstructure of Fe-Mn-C TWIP Steel

The influences of impurity content, tensile strength, and grain size on in-service temper embrittlement of CrMoV steels

Research on Fatigue-Creep Interaction Damage of Steel 1.25Cr0.5mo

Regulation Law of Tempering Cooling Rate on Toughness of Medium-Carbon Medium-Alloy Steel

Effects of the Addition of Alloying Elements on Hydrogen Diffusion and Hydrogen Embrittlement in Martensitic Steel

The effect of grain size on fracture behaviour in tempered martensite embrittlement for AISI 4340 steel

Effect of Delta Ferrites on the Anisotropy of Impact Toughness in Martensitic Heat-Resistant Steel

ON THE TIME-DEPENDENT MATERIAL FRACTURE TOUGHNESS AT HIGH TEMPERATURE

Fatigue Fracture Behavior of High Strength Cr-Mo-V Steel

Effect of Tempering Temperature and Carbide Free Bainite on the Mechanical Characteristics of a High Strength Low Alloy Steel

Cyclic Softening Properties of 30cr2mov Steel at Elevated Temperatures

A prediction model of brittle crack arrest toughness in TMCP heavy plates

Microstructure and Notched Fracture Resistance of Low Alloy 0.56% C Steels after Simulated Induction Hardening

A Coupled EBSD/TEM Analysis of the Microstructure Evolution of a Gradient Nanostructured Ferritic/Martensitic Steel Subjected to Surface Mechanical Attrition Treatment

Fractal Characterization of the Fracture Surface of Untempered and Tempered Bainitic Modified 9Cr-1Mo Steel

Strengthening and Toughening Mechanisms in Martensitic Steel

Effect of Trace Mg on Impact Toughness of 2.25Cr1Mo Steel Doped with 0.056% P at Medium Temperature Aging Process

Effect of Carbides on High-Temperature Aging Embrittlement in 12%cr Martensitic Heat-Resistant Steel