Abstract:Ni improves toughness in martensitic steels. However, the effect of Si on grain refining and toughness of martensitic steel for high-strength applications including armor grades has not been much studied, which can be also a cheaper alternative replacing Ni and without any micro-alloying addition. With this motivation, an initial laboratory study of a quenched and tempered high-Si steel (0.31C-1.25Si-1.19Mn-0.1Mo-0.29Ni) and low-Si steel (0.32C-0.49Si-0.61Mn-0.46Cr-0.1Mo-0.29Ni) showed that their full thickness Charpy impact energy at − 40 °C was 32 ± 3 and 15 ± 2 J, respectively, while their microstructures had maximum lath length 15 and 30 μm, respectively. Based on this, an industrial steel (0.30C-1.27Mn-1.23 Si-0.22 Mo-0.43Ni) was made through electric arc furnace—vacuum arc degassing—continuous casting route with low H2, O2 and N2 contents and hot rolled to 5.2-mm-thick coil, which finally processed to quenched and tempered plate. The air-cooled hot-rolled intermediate plate of 25 mm thickness revealed bainitic microstructure, while the slowly cooled hot-rolled coil sample showed banded microstructure consisting of proeutoctoid ferrite and pearlite. On the other hand, the ferrite bainitic microstructure was revealed when the steel was cooled at 1 °C/s through dilatometry using Gleeble 3500C. The bainitic microstructure at low cooling rate indicated high hardenability of this grade. The Ac3 transformation temperature determined by dilatometry was 850 °C. Based on this, oil quenching was carried out after heating at 895 °C for 7, 12 and 17 min, while low-temperature tempering was done at 250 °C for 60 min. The micrographs in these three heating conditions revealed fully martensitic microstructure consisting of fine laths. The hardness of plates varied in the range of 495-506 HBW after tempering at 250 °C for 1 h, while yield strength, tensile strength, percentage elongation and percentage of reduction in area varied in the range of 1500-1540, 1780-1820 MPa, 7.37-8.61 and 24.64-27.40, respectively. The Charpy impact energy of sub-size ½ thickness specimen varied closely in the range 11.5-13.8 J at − 40 °C and their corresponding fracture surfaces showed dimpled ductile rupture morphology that typically belonged to the upper shelf region of Charpy transition curve. The measured hardness, strength, elongation and Charpy energy are in accordance with the requirement of final product. Bright-field TEM image of the tempered steel showed the presence of fine laths and uniformly distributed needle-shaped fine carbides resembling ε-Fe2.4C.

Microstructure and Notched Fracture Resistance of Low Alloy 0.56% C Steels after Simulated Induction Hardening

Insight into the induction hardening behavior of a new 0.40% C microalloyed steel: Effects of initial microstructure and thermal cycles

Short time austenitizing effects on the hardenability of 0.55 wt. pct. Carbon steels

Low Cycle Fatigue and Creep Fatigue Interaction Behavior of 9Cr-0.5Mo-1.8w-v-nb Heat-Resistant Steel at High Temperature

Interpretation of Significant Decrease in Cryogenic-Temperature Charpy Impact Toughness in a High Manganese Steel

Tailoring the Microstructure to Enhance the Cryogenic Mechanical Properties of a Fe–34.5mn–0.04c Steel

Favorable Impact Toughness of High Heat Input Coarse-Grained HAZ in an Ultra-Low Carbon High-Strength Microalloyed Steel

Effect of Rapid Heating and Quenching on Microstructure and Mechanical Properties of High Strength Low Alloy Steel

N-induced Microstructure Refinement and Toughness Improvement in the Coarse Grain Heat-Affected Zone of a Low Carbon Mo–V–Ti–B Steel Subjected to a High Heat Input Welding Thermal Cycle

Microstructure and Hardening Behavior of Al-modified Fe-1.5 Wt%b-0.4 Wt%c High-Speed Steel During Heat Treatment

Effect of Pre- and Post Weld Heat Treatment on Microstructure Development and Mechanical Properties of 0.3%C-CrMoV (ESR) High-Strength Low-Alloy Steel

The In Situ Observation of Phase Transformations During Intercritical Annealing of a Medium Manganese Advanced High Strength Steel by High Energy X-Ray Diffraction

Deformation microstructures as well as strengthening and toughening mechanisms of low-density high Mn steels for cryogenic applications

Simulation and experimental studies of induction hardening behavior of a new medium-carbon, low-alloy wear resistance steel

Influence of an Electric Field on the Quench Aging of a Medium-Carbon Alloy Steel

Effects of Ni on Austenite Stability and Fracture Toughness in High Co-Ni Secondary Hardening Steel

Effect of Niobium Content on the Microstructure and Mechanical Properties of Simulated Coarse-Grained Heat-Affected Zone (CGHAZ) of High-Strength Low-Alloy (HSLA) Steels

Strengthening and Toughening Mechanisms in Martensitic Steel

A study of the abrasive wear of carbon steels

High-Si-Content Quenched and Tempered Steel for High-Strength Application

Improving the Low-Temperature Toughness of a High-Strength, Low-Alloy Steel with a Lamellarization Heat Treatment